Before connecting other devices to the mixer, all units have to be switched off and the Master Control (6) set to min. • Make sure that the available voltage is not higher than stated on the voltage selector (22) before connecting to power. • In order to obtain the highest sound quality, only use high quality American DJ®, Ameri-Cable™ cables for connecting devices. Make sure that the cables are properly fixed. • Connect your amplifier to the OUT AMP jacks (19). Make sure that the channels are s

& CANADA MODEL ONLY CAUTION TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE CAREFULLY INSERTED TO PREVENT BLADE EXPOSURE WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS MEDIA PLAYER TO WATER OR MOISTURE CAUTION: USE OF CONTROLS OR ADJUSTMENTS OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE THE MEDIA PLAYER SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT PROPERLY QU

2. Please visit our website at and register your warranty at the “Register Your Warranty Here” text, or complete the Warranty Registration Card and return it to the factory. DESCRIPTION FRONT PANEL NOTE: Descriptions for Channels 1 - 8 are identical. TRIM: Adjusts the sensitivity of the XLR Microphone Inputs. LEVEL: Adjusts the level of signal in the channel from off to +20 dB of gain. TONE:Cuts the signal up to 12 dB, below 200 Hz when turned clockwise, or above 6 when turned counter-clockwise.

Turntables should only be connected to “Phono” inputs. The red colored RCA jack represents the right channel input and the white represents the left channel input. Input volume will be controlled by channel three Channel Fader (9). The channel Source Selector Switch (5) must be in the "Line 3" position, to monitor any source connected to these jacks. 43. CHANNEL 3: PHONO 3 INPUT/AUX 3 JACKS - The type of input must directly refl ect the selected mode of the Line Level Selector Switch (5). Connec

10 Thank you for purchasing this American DJ® product. The Q-2221/X Is ready to be used, there Is no assembly required. Please read the following Instructions before installing or using your new unit. The Q-2221/X has a 2 year limited warranty! CAUTION! - Keep this device away from rain and moisture! Safety Instructions Always plug in the power last. Make sure that the Power switch is set to the OFF position before connecting other devices to the mixer. Keep away from heaters and other heat

After pressing one of the FLASH BUTTONS (6), the corresponding Flash Button LED will flash briefly. The LED will remain lit indicating either a sample or cue point is stored in memory. The red Memory Cue LED will now shut off. Figure 17 Figure 18 2) Repeat the above steps to store up to three Cue Points. Once all your three cue points have been stored you may access them at any time. The cue points will instantly start without any music interruption. Please note in order to access these cue p

Never touch the lamp with bare fingers, as the oil from your hands will shorten the lamp life. Also, never move fixture until lamp has had ample time to cool. Remember, lamps are not covered under warranty conditions. DMX-512 FOR SYNCHRONIZING Model: ONYX II™ SPECIFICATIONS: Voltage: 120V Lamp: EXY 82v / 250w Dimensions: 12.25" x 5.5" x 11" Weight: 18 lbs. Fuse: 5A Working Position: Any safe position Cooling: Fan Cooled Duty Cycle: 30 min. ON, 10 min. OFF Gobos: 16 / Plus Spot - fixed Col

CAUTION: Use of controls, adjustments, or procedures other than those specified herein may result in hazardous radiation exposure. This product is a chase controller of 8 movable red laser diode, which allows you to control the chase patterns, speed, motor movement and laser beam. This product has 9 built-in chase patterns and 8 adjustable speeds, any of the 9 patterns can be operated in Audio/Chase mode. The motor movement can be operated in Music/ Auto mode. Also, the laser beam can chase or

Never touch lamp iwith bare fingers as the oil from your lhands will shorten lamp life. Also, never •move fixture until lamp has had ample ¡time to cool. Remember, lamps are not icovered under warranty conditions. Caution! Always disconnect from main power before replacing lamps or servicing unit. Remember to always replace with same lamps and fuses. Model: Multi-Saucer™ SPECIFICATIONS: Lamp: 5 x ZB-FCS 24V 150W Dimensions: 18” x 18” x 16.5” Weight: 21 lbs. Supply Voltage: 120V Fuse: 10A

Phone 716 663-8820 . Fax 716 865-8930 . Email: Sales@whirlwindusa.com . 8S S8 Maximum Output Level +22 dBm Rise Time 6 uS POWER RL87 54321 INPUTS 120 Vac at 60 Hz 230 Vac at 50 Hz 25 watts MAX U.S. AUDIO A DIVISION OF WHIRLWIND INC ROCHESTER, NY USA MONO RIGHT/ : DEBRANCHER AVANT D'OUVRIRATTENTION LEFT MAIN OUT STEREO ALL CONNECTORS BALANCED TIP+, RING-, SLEEVE GND : TO PREVENT ELECTRIC SHOCK DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. :