MAIN COMPONENTS of PHV Series constant pressure variable speed system • One multistage vertical pump, Goulds Pumps SSV series. • Hydrovar® pump mounted variable speed drive • Pressure transducer for constant pressure control, connected to the Hydrovar drive. • NEMA 4X fused disconnect panel with corrosion resistant durable plastic; external on/off switch with lockout/tagout. Panel is bracket mounted directly to pump. • Electrical panel for control and protection, with casing made of plastic mate

Gas engine power outputs must be approximately twice the pump power requirements shown above. We recommend a 1.1 service factor be specified when selecting an electric motor as the power source. To compute specific pump horsepower requirements, use the following formula: GPM X PSI 6 GP7132 AND GP7136 REPAIR INSTRUCTIONS NOTE: Always take time to lubricate all metal and non-metal parts with a light film of oil before reassembling. This step will help ensure proper fit, at the same time pro

Gas engine power outputs must be approximately twice the pump power requirements shown above. We recommend a 1.1 service factor be specified when selecting an electric motor as the power source. To compute specific pump horsepower requirements, use the following formula: GPM X PSI 1400 3 GP7132 and GP7136 PARTS LIST ITEM PART DESCRIPTION OTY. I 07600 Crankcase 1 2 13000 Oil Filler Plug Assembly 1 4 07601 Crankcase Cover 1 5 07602 Seal for Cover 1 8 07603 Oil Dip Stick 1 9 01009 O-Rin

46A 07064-0100 Valve Seat 3 46B 07063-0100 Valve Plate 3 46C 07750-0100 Valve Spring 3 44A 07150 O-Ring 6 44B 06266 Support Ring 3 ITEM PART DESCRIPTION QTY 1 07759 Crankcase 1 2 13000 Oil Filler Plug Assy... 1 4 06085 Crankcase Cover 1 5 07104 O-ring, Crankcase Cover 1 6 07186 Oil Sight Glass w/Gasket 1 7 07187 Gasket (For Sight Glass) 1 8 06086 Oil Dipstick Assy. 1 9 01009 O-Ring, (For Dipstick) 1 10 08093 Cylinder Screw 4 11 08094 Spring Ring 5 12 12137 Plug, G1/2" 1 13 07182 Gasket 1 14 0711

Tuck the two outside edges of the figure 8 into the rear of the retainer, making sure that the inner lip of the seal faces the oil. The seal may now be pressed firmly into place. TO REASSEMBLE PROCEED AS FOLLOWS: 9. The front oil seal (31A) can now be removed by inserting a screwdriver through the rear of the retainer and tapping the seal out through the front of the retainer. Remove any excess old loc-tite from retainer. To replace oil seal, apply a light film of loc-tite around outside edges o

Inlet Por. ............................................................................................ 1-1/2" NP. Discharge Por. ................................................................................... 1" NP. Crankshaft Mountin. ......................................................................... Either Sid. Shaft Rotatio. .................................................................................... Top of Pulley Towards Fluid En. Weight...................................

0.9. Mechanical Efficiency @ 800 RPM.................................................. 0.8. PULLEY INFORMATION HORSEPOWER INFORMATION Pulley selection and pump speed are based on a 1725 We recommend that a 1.1 service factor be specified RPM motor and "B" section belts. When selecting when s electing an electric motor as the power source. desired GPM, allow for a ±5% tolerance on pumps To compute specific pump horsepower requirements, output due to variations in pulleys, belts and motors use the

35A 07740 O-ring 3 36 13415 V-Sleeve, Weep 3 40 07745 V-Sleeve 6 Plunger Packing Kit # 09535 (LP255) Item Part # Description Qty. 35A 07740 O-ring 3 35B 13141 O-Ring 3 36 13025 V-Sleeve weep 3 40 13027 V-Sleeve 6 Valve Assembly Kit LP122A. LP123, LP122A-4000, LP255 #09136 Item Part # Description Qty. 46A 07751 Valve Assembly, Complete 3 48A 12055 O-Ring 3 Valve Assembly Kit LP122A-3100 #09305 Item Part # Description Qty. 46. 07751-010. Valve Assembly Complet. . 48A 06577 O-Ring 3 LP122A SERIES/L

This is necessary to ensure proper curing of new loc-tite. Giant recommends cleaning the threads with acetone or other suitable cleaner. Reassemble plunger assembly parts (29A, 29B, & 29E) using a new copper gasket (29D) and the cleaned plunger bolt (29C). Slide the bolt through the center of the four (4) pieces so that the threaded end is exposed. Apply several drops of loc-tite 243 (or equivalent) adhesive to the threads. Thread into steel plunger base and tighten to 26 ft.-lbs. BE CERTAIN ALL

oz. Temperature of Pumped Fluids.............................................................Up to 80 °F Inlet Port...............................................................................................1 x 1/2" NPT Discharge Ports....................................................................................3/8" NPT Shaft Rotation.......................................................................................Clockwise Weight...............................................