Log:
Évaluations - 4, GPA: 3.8 ( )

Instructions Kompernass, Modèle PFLK15

Fabricant : Kompernass
Taille : 82.11 kb
Nom Fichier : 7928204c-25e6-3214-d969-ff67e67eca1b.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


300° C BEFORE USING FOR THE FIRST TIME . Please read the safety advice for electric tools in the section on "Safe . Before using the tool for the first time check that your mains voltage with that on the rating plate. . Before heating the tool check that the soldering tip is firmly seated must be fully tightened. . Connect the soldering pencil to the mains supply. . When removing the soldering tip make sure that the soldering pencil is switched off and do not use too much force. Slide a new soldering tip fully in so that it hits the stop. . Do not heat up the soldering pencil without . After use let the soldering pencil cool down Under no circumstances quench the tip in water! . Place the soldering pencil in the stand . To avoid the risk of fire we recommend that you place the soldering resistant support pad. . Do not use the soldering pencil always use an electrical equipment centre or the service centre indicated for your country. 4 RANGE OF USE The PARKSIDE soldering pencil PFLK 15, with its nominal 15 watt power rating, is ideal for soldering components and circuit boards. The nominal soldering tip temperature is about 320° C. For best results use electronics solder 1.0 (10 g included with the soldering pencil) or 1.5 mm dia. 60 % Sn. We recommend soldering paste (not soldering grease or soldering fluid) as a flux. The design of the soldering pencil makes it especially suitable for use where access is difficult or for fine soldering work. The interchangeable tips increase the versatility of the soldering pencil. SAFE OPERATION 1. Check the mains voltage. Please make sure that the available mains voltage corresponds to that shown on the rating plate on the equipment. 2. Switch equipment on before placing into contact with Always turn on the equipment before placing it into contact with the workpiece. 3. Keep your working area tidy. Untidiness at your working area may lead to accidents. 4. Take surrounding influences into consideration. Do not subject power tools to rain. Do not use power environment. Ensure good lighting. Do not use power tools close 5. Protect yourself against an electric shock. Avoid physical contact with earthed parts such 6. Keep out of reach of children. Do not let others tough the tool or the your working area. 7. Store your tools in a safe place. Tools not being used should be stored in a dry, high and closed place, out of the reach of children. 8. Do not overload your power tools. Your work is safer and better if carried 9. Use the correct power tool. Do not use machines of insufficient capacity for heavy-duty those for which they are intended, for example do saw for cutting tree trunks and timber. 10. Wear appropriate workwear. Do not wear wide clothes open, rubber gloves Wear a hair net if you 5 11. Wear eye protection, protective mask and ear defenders. For work which produces splinters, swarf or dust or when working overhead always wear eye protection, with an appropriate protective mask. When working in noisy conditions, wear ear defenders. 12. Connect the dust suction device. If devices for the connection of dust suction equipment and collectors are available, ensure that these are connected and properly used. 13. Use cable only for such purposes for which it is intended. Never carry the power tool by the cable. Do not use cable to disconnect the tool from the mains supply. Protect the cable against heat, oil and sharp edges. 14. Secure the work piece. Use a fastening device or a vice to secure the work. This guarantees a safer hold than with a single hand and allows you to operate the power tool with both hands. 15. Avoid abnormal posture. Get a firm stand and hold your balance at any time. 16. Service your tools carefully. Keep your tools clean and sharp to be able to perform better and and the note regarding change of tools. Check the cable of the tool regularly and in case of damage, ask for professional repair. Check extension cables regularly and replace them if damaged. Keep handles dry and free of oil and grease. 17. Disconnect the mains plug. When power tool is not used, before maintenance and when changing tools, such as saw 18. Always remove tool keys. Before switching on device, ensure that the keys and adjustment tools are removed. 19. Avoid unintended start. Do not carry any tools connected to the mains supply that the switch is off when plugging instrument into socket. 20. Extensions in the open. Only use authorized and respectively marked extensions for use in the 21. Be attentive. Pay attention to what you are doing. Act sensibly. Do not use the power tool if you are not fully concentrating. 22. Check the power tool for any possible Before further use of the power tool, the devices or any lightly damaged parts must be carefully examined. Check whether the and do no jam or if any parts damaged. All parts must be mounted correctly and meet all conditions devices and parts must be repaired professionally by a recognized expert workshop Damaged switches must at...


Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories