Évaluations - 4, GPA: 4
(
)
)
|
Facilité d'utilisation
•The front panel may become hot in normal usage (especially the connector terminals on the back of the front panel). This is not a malfunction. •To protect the front panel, place it in the supplied carrying case. •When detaching the front panel, do not apply excessive force as it may result in malfunction. Attaching 1Insert the right side of the front panel into the main unit. Align the groove on the front panel with the projections on the main unit. 2Push the left side of the front panel until it locks firmly into the main unit. •Before attaching the front panel, make sure that there is no dirt or dust on the connector terminals and no foreign object between the front panel and the main unit. •Attach the front panel carefully, holding the sides of the front panel to avoid pushing buttons by mistake. Initial System Start-Up Be sure to press the RESET switch when using the unit for the first time, after changing the car battery, etc. 1Turn off the unit power. 2Remove the detachable front panel. 3Press RESET with a ballpoint pen or similar pointed object. 1RESET switch Adjusting Volume Turn the Rotary encoder (CDE-9874 Series only) or press and (CDE-9872 Series only) until the desired sound is obtained. Connectable to Steering Remote Control Interface Box You can operate this unit from the vehicle’s control unit when an Alpine Steering Remote Control Interface Box (optional) is connected. For details, contact your Alpine dealer. Radio CDE-9874 Series BAND/TAPreset buttons(1 through 6) TUNE/A.MESOURCE/ FUNC./SETUP CDE-9872 Series BAND/TAPreset buttons(1 through 6) TUNE/A.MESOURCE/ FUNC./SETUP Listening to Radio 1Press SOURCE/ to select TUNER mode. 2Press BAND/TA repeatedly until the desired radio band is displayed. F1 (FM1) F2 (FM2) F3 (FM3)* MW LW F1 (FM1) *When CDE-9872RE is connected, the received frequency band is F3 (LOW BAND). 3Press TUNE/A.ME to select the tuning mode. DX SEEK (Distance mode) SEEK (Local mode) OFF (Manual mode) DX SEEK •The initial mode is Distance mode. Distance mode: Both strong and weak stations will be automatically tuned in (Automatic Seek Tuning). Local mode: Only strong stations will be automatically tuned in (Automatic Seek Tuning). Manual mode: The frequency is manually tuned in steps (Manual tuning). 4Press or to tune in the desired station. Holding down or will change the frequency continuously. Presetting Stations Manually 1Select the radio band and tune in a desired radio station you wish to store in the preset memory. 2Press and hold, for at least 2 seconds, any one of the preset buttons (1 through 6) into which you wish to store the station. The selected station is stored. The display shows the band, preset number and station frequency memorized. •A total of 30 stations can be stored in the preset memory (6 stations for each band; FM1, FM2, FM3, MW and LW). •If you store a station in a preset memory which already has a station, the current station will be cleared and replaced with the new station. •If the indicator is illuminated, turn off the indicator by pressing FUNC./SETUP, and then you can perform the operation. Presetting Stations Automatically 1Press BAND/TA repeatedly until the desired radio band is displayed. 2Press and hold TUNE/A.ME for at least 2 seconds. The frequency on the display continues to change while the automatic memory is in progress. The tuner will automatically seek and store 6 strong stations in the selected band. They will be stored into preset buttons 1 to 6 in order of signal strength. When the automatic memory has been completed, the tuner goes to the station stored in preset location No.1. •If no stations are stored, the tuner will return to the original station you were listening to before the auto memory procedure began. Tuning to Preset Stations 1Press BAND/TA repeatedly until the desired band is displayed. 2Press any one of the station preset buttons (1 through 6) that has your desired radio station in memory. The display shows the band, preset number and frequency of the station selected. •If the indicator is illuminated, turn off the indicator by pressing FUNC./SETUP, and then you can perform the operation. RDS CDE-9874 Series VIEWBAND/TA //ENTRotary encoder/SOUND1/AFFUNC./SETUP CDE-9872 Series BAND/TA //ENTVIEW1/AFFUNC./SETUP/AUDIO Setting RDS Reception Mode and Receiving RDS Stations The RDS (Radio Data System) is a radio information system using the 57 kHz subcarrier of regular FM broadcast. The RDS allows you to receive a variety of information such as traffic information, station names, and to automatically re-tune to a stronger transmitter that is broadcasting the same programme. 1Press FUNC./SETUP so that the indicator lights up. 2Press 1/AF to activate the RDS mode. 3Press or to tune in the desired RDS station. 4Press 1/AF again to deactivate the RDS mode. 5Press FUNC./SETUP to activate the normal mode. The indicator goes out. •Operate the unit while the indicator lights up. If no operation is performed for 10 seconds, the indi...
Ce manuel est également adapté pour les modèles :Lecteurs - CDE-9874RR (1010.71 kb)
Lecteurs - CDE-9874RB (1010.71 kb)
Lecteurs - CDE-9874R (1010.71 kb)
Lecteurs - CDE-9872RM (1010.71 kb)