Évaluations - 4, GPA: 4.3
(
)
)
|
Facilité d'utilisation
HBS – Press so that the HBS indicator lights. You can enjoy powerful bass sound with the Hyper-Bass Sound effect. POWER OFF – Move FUNCTION to OFF/TAPE with no cassette button pressed, to turn the unit off. USING THE RADIO TUNING IN RADIO STATIONS Move FUNCTION to TUNER to turn the radio on. • Set BAND to AM or FM. • Tune in desired station by turning the TUNING knob. • To turn off the radio, move FUNCTION to OFF/TAPE. BEAT CUT/FM MODE SWITCH • When recording an AM broadcast When recording an AM broadcast, beats may occur. If this happens, set the switch to “1” or “2.” • Changing the FM reception mode When an FM stereo broadcast is hard to receive or noisy, set the switch to “MONO.” Reception improves. To restore the stereo effect, switch to “STEREO.” USING THE TAPE PAUSE – Press to interrupt tape play or record mode. Press a second time to resume tape play or tape record mode. STOP/EJECT – Press to stop the current tape activity, or to open the cassette compartment door when no buttons are active. FF – In stop mode, press to advance the tape toward the end. (When the tape reaches the end, press STOP/EJECT to release the depressed button.) REW – In stop mode, press to rewind the tape toward the beginning. (When the tape reaches the end, press STOP/EJECT to release the depressed button.) PLAY – Press to play cassettes. REC – Press to record from the radio or CD player. PLAYING A CASSETTE TAPE 1. Move FUNCTION to OFF/TAPE. 2. Press STOP/EJECT to open the cassette compartment door. 3. Insert a cassette tape into the compartment with the exposed part of the tape facing up and the side you want to play facing toward you. 4. Close the door securely. 5. Press REW or FF to move the tape to the desired starting point. 6. Press PLAY to begin playing the tape. The cassette tape plays until it reaches the end of the side, then it automatically stops. RECORDING ON CASSETTE TAPES You can record from the radio or the CD player. For best recording, use normal bias tape. It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs without the consent of the owner of copyright in the sound or video recording, broadcast or cable program and in any literary, dramatic, musical, or artistic work embodied therein. ERASE PROTECTION When you record new material, the cassette deck records over whatever is on a tape. To protect a tape from accidental erasure, break off one or both plastic tabs (one for each tape side) on the top of the cassette tape. If you decide later to record on the tape, seal the hole with a piece of cellophane tape. WARNING A little bit of slack in your tape can cause scratches on the tape, or worse yet, the tape could break. If you notice some slack in the tape, use a pencil to tighten it up before you insert it in the tape deck. TIP The use of tapes longer than 120 minutes is not recommended, since characteristic deterioration may occur and these tapes easily jam in the pinch-roller and the capstan. RECORDING FROM THE RADIO 1. Insert a cassette tape into the tape deck and close the door. 2. Move FUNCTION to TUNER and select a radio station. 3. Press REC to begin recording. REC and PLAY lock down. 4. Press STOP/EJECT to end recording. 5. To turn off the radio, slide FUNCTION to OFF/TAPE. RADIO RECORDING TIPS • To temporarily pause the recording, press PAUSE on the cassette deck. Press PAUSE again to resume recording. SYNCHRONIZED RECORDING FROM A CD 1. Insert a cassette tape into the tape deck and close the door. 2. Move FUNCTION to CD. 3. Insert the CD you want to record into CD compartment. 4. Select the track you want to record by pressing (skip/search) or (skip/search). 5. Press REC to start recording. Note that the tape continues to run when the CD finishes playing, or the CD continues to play when the tape reaches the end. TIP Using the PAUSE button on the cassette deck instead of the STOP/EJECT button to momentarily interrupt recording gives you a much cleaner sound recording. U USING THE CD PUSH PLAY/PAUSE STOP HBS HBS REPEAT RANDOM PROGRAM CD PLAY MODE REMOTE SENSOR LOADING A CD 1. Move FUNCTION to CD; “– –” flashes, then “no” appears in the display if no CD is loaded. 2. Press ) PUSH to open the CD door. 3. Place a CD into the tray with the label facing up. 4. Close the CD door. Then the total number of tracks appears. 5. To remove the CD, press ) PUSH, grasp the CD by its edges, and carefully pull it out. PLAYING A CD Press PLAY/PAUSE to play all the tracks in order starting with track 1. The current track number appears in the display. Note: Press PLAY/PAUSE to temporarily stop the CD. The indicator and the track number flash in the display. Press PLAY/PAUSE again to resume playing the CD. • Adjust VOLUME to a comfortable level. • Press STOP 7 to stop playing the CD. Wait a few seconds for the CD to stop turning, then press ) PUSH to open the CD compartment door and remove the CD. AUTOMATIC SEARCH Automatic search lets you quickly locate the beginning of any track o...
Ce manuel est également adapté pour les modèles :Lecteurs - RC-EX10A (357.07 kb)
Lecteurs - RC-EX10B (357.07 kb)