Évaluations - 4, GPA: 4
(
)
)
|
Facilité d'utilisation
If the ohmmeter reads zero or open, the cell should be checked for dirt on the face or shorted leads. If the face of the photocell is dirty, clean with soft cloth and replace. Check for the resistance change in the photocell from no flame to flame. If the cell still reads zero or open check the wiring from one end to the other for opens and across the leads for shorts. If no problem is found replace the cell and check once again for the resistance change. 5. If the photocell and primary safety control function properly, the problem is that the heater is not burning properly. 6. If the control fails to shut down the heater, it is defective and must be replaced. 7. After replacing control system components, test fire the heater to make sure it will function properly. If it does not, check all wiring connections according to the wiring diagram, Figure 2. Repeat the testing procedure if necessary. TUNE UP To keep your heater in top operating condition, perform the following services at the start of each heater season then at the interval specified below: CLEAN AND/OR REPLACE FUEL FILTER Clean at least twice a season. More often if heater performance indicates the need. Replace if necessary. CLEAN FAN Clean fan after every 500 hours of operation. Clean more frequently if heater is operating in dusty areas or if there is a build-up of dirt on the blades. REPLACE BURNER NOZZLE Replace nozzle at least once during the heater season or more often if heater performance indicates the need. CLEAN AND ADJUST SPARK PLUG After every 300 hours of operation, clean and adjust spark plug electrodes. Adjust gap or replace the plug if electrodes have been burned, erroded, or carboned. CLEAN PHOTOCELL Clean the photo cell face with a soft cloth at least once during the heater season. If cell face tends to soot up, check with your nearest service station to determine the cause. FUEL PUMP MAINTENANCE AND SERVICE 1. The pump operates at 105 PSI. To check pressure, remove the hex head pipe plug from the port marked gauge on the fuel pump and install a pressure gauge. 2. If the pressure gauge does not read 105PSI,plusor minus 5 PSI, when the motor is running and pumping fuel, adjust the pump. 3. Remove the access plug on the side of the pump body marked pressure adjustment. To increase the fuel pressure, turn the slotted screw inside the port clockwise. To decrease the fuel pressure, turn the screw inside the port counterclockwise. After completion of the adjustment install the plug into the adjusting port, then remove the gauge. Install the plug into the fuel pump. If the fuel pressure cannot be adjusted, replace the pump. FORM 5S2514 MODEL 3E358 01582 ORDER REPLACEMENT PARTS THROUGH DEALER FROM WHOM PRODUCT WAS PURCHASED Please provide following information: • Model Number • Serial Number (if any) • Part Description and Number as shown in parts list. If dealer cannot supply, order from: Dayton Electric Mfg. Co. Parts Department 5959 West Howard Street Chicago, Illinois 60648 Figure 5— Replacement Parts Illustration for Model 3E358 —5— FORM 5S2514 MODEL 3E358 01582 Replacement Parts List for Model 3E358 REF. NO. PART NO. DESCRIPTION QTY. REF. NO. PART NO. DESCRIPTION QTY. 1 M50060AZ Upper shell 1 23 M11271-6 Clip nut (Tinnerman) 16 2 M11084-27 #10-12 x 1/2” screw 16 24 M50062-03 Front handle 1 3 M50089 Wiring diagram decal 1 25 M51043-01 Hex capscrew» 2 4 M50097-01AA Fan guard 1 26 HC4-18C Screw(1/4-20 x 21/4")» 6 5 M50099-02 Combustion chamber& 27 M50062 Rear handle 1 ^605^-0 j heat deflector 1 28 M18053 Filler neck screen 1 6 M50086 Air deflector 5 30 M50115-04 Fuel line assembly , 1 7 M30865-02 Short bushing 8 31 M50071-01AA Fuel tank assembly 7 1 8 M51129-03 Burner head assembly 32 M23284 Fuel tank cap 1 (see Fig u re 9 fo r detai Is) 1 33 NTC-4C Hex locknut (1/4-20) 8 9 M50121 Fan 1 34 M25297-14 Thermostat assembly 1 10 M50230 Safety control 1 35 M27417 Drain plug 1 11 M51336-02 Fan switch (kit, incl. 44) 1 36 M50063 Wheel support frame 1 12 M13942-5 Connectorwire 4 37 WP-10C Flatwasher(5/8” I.D.) 4 13 M50104-02 Short bushing 3 38 M50389 Wheel 2 14 M11084-27 Screw #10-12 x 1/2” 14 39 C5-10C Cotter pin (5/32 x 11/4") 2 15 M50295 Fuel line 1 40 M18774 Axle (5/8" Dia.) 1 16 M50391-01 Wire harness assembly 1 41 M11084-26 Hex head screw (#10x1/2) 20 17 M13942-7 Wire connector 4 42 M16656-4 Photo cell assembly 4 18 M50079-04 Motor & pump assembly^ — 43 M51160-01 Fan switch cover 1 19 M10813-88 Extension cord assembly A M50278 Sleeve (located on motor 1 (Power cord) 1 shaft, between fan & 20 M50050 Ignition boot 1 motor) 21 M50570-02 T ransformer 5000 volt A M50296 Wheel spacer and bracket 1 22 M50061AZ Lower shell 1 iNot available as complete assembly. See Figure 6for details. ANot shown. •Holds handle in position Figure 6— Replacement Parts Illustration for Motor Replacement Parts List for Model 3E358 Motor & Pump Assembly REF. NO. PART NO....
Ce manuel est également adapté pour les modèles :Plate - 3E359 (717.24 kb)