Évaluations - 3, GPA: 4.7
(
)
)
|
Facilité d'utilisation
352. Using a network-connected machine Disconnecting from a network 1 Press the (Menu) button on the control panel. To disconnect the wireless network connection, press the (WPS) button on the control panel for more than two seconds. • When the Wi-Fi network is in idle mode: The machine is immediately disconnected from the wireless network, and the WPS LED is off. • When the Wi-Fi network is being used: While the machine waits until the current job is finished, the light blinks fast on the WPS LED. Then, the wireless network connection is automatically disconnected. The WPS LED is off. ....Using the menu button Before starting, you will need to know the network name (SSID) of your wireless network and the network key if it is encrypted. This information was set when the access point (or wireless router) was installed. If you do not know about your wireless environment, please ask the person who set up your network. After completing the wireless network connection, you need to install a machine driver to print from an application (see "Installing driver over the network" on page 17). 2 2 Press Network > OK > Wireless > OK > WLAN Settings > OK. 3 3 Press the OK to select the setup method you want. • Wizard: The wireless network interface card in your machine searches for wireless networks in the area and shows the results. • Custom: You can configure the wireless settings according to your needs. Wizard mode 1 1 The wireless network interface card on your machine searches 2 2 for wireless networks in the area and shows the results. Press Search List > OK > select a the network > OK. 3 3 You can select a network using SSID. Press WLAN Security > OK > None > OK. If you see another message, go to the next step. 3636 Wireless network setup 4 4 According to the network you selected, the WLAN security encryption type will be WEP or WPA. •In case of WEP, press the Open System or SharedKey. -Open System: Authentication is not used, and Encryption may or may not be used, depending on the need for data security. Enter the WEP Key after selecting Open System. - SharedKey: Authentication is used. A device that has a proper WEP Key can access the network. Enter the WEP Key after selecting SharedKey. •In case of WPA, enter the WPA Key. The key length should be between 8 and 63 characters long. 5 5 Press OK. Custom mode 1 1 Enter the SSID when Edit SSID appears on the top line of the display, the name that identifies a wireless network. SSID is case-sensitive so you need to enter it carefully. Press OK. 2 2 Select the type of wireless connections. 2. Using a network-connected machine 3 3 Press OK to select the method of Operation Mode. • Ad-hoc: Allows wireless devices to communicate directly with each other in a peer-to-peer environment. Go to step 4. • Infrastructure: Allows wireless devices to communicate with each other through an access point. Go to step 5. 4 4 Press OK to select the method of Channel. If you select Auto, the wireless network interface card on your machine will automatically adjust the channels. 5 5 Press OK to select the method of WLAN Security. • None: This is used when the validation of a wireless device’s identity and data encryption are not required for your network. Open system is used for IEEE 802.11 authentication. • Static WEP: This uses the WEP (Wired Equivalent Privacy) algorithm suggested by IEEE 802.11 standard for security. Static WEP security mode requires a proper WEP key for data encryption, decryption, and IEEE 802.11 authentication. Press OK to select the setup method in Authentication - Open System: Authentication is not used, and encryption may or may not be used, depending on the need for data security. Enter the WEP Key. Wireless network setup 372. Using a network-connected machine -SharedKey: Authentication is used. Enter the WEP Key after selecting SharedKey. .... 16 Setup using Windows 372. Using a network-connected machine -SharedKey: Authentication is used. Enter the WEP Key after selecting SharedKey. .... 16 Setup using Windows • WPA-PSK or WPA2-PSK: You can select WPA-PSK or WPA2-PSK to authenticate the print server based on WPA Pre-Shared Key. This uses a shared secret key (generally called Pre-Shared Key passphrase), which is manually configured on the access point and each of its clients. a Press OK when WPA-PSK or WPA2-PSK appears of on the display. b Press OK to select TKIP or AES in Encryption. If you select WPA2-PSK, press OK to select AES or TKIP + AES in Encryption. c Enter the WPA Key. 6 6 Press OK. Disconnect the network cable (standard or crossover). Your machine should then start communicating wirelessly with the network. In case of Ad-hoc mode, you can use a wireless LAN and wired LAN simultaneously. Shortcut to Wireless Setting program without CD: If you have installed the printer driver once, you can access the Wireless Setting program without CD. From the Start menu, select Programs or All Programs > Samsung Printers > your printer driver name > Wireless S...
Ce manuel est également adapté pour les modèles :Imprimantes - ML-2950D (10.94 mb)
Imprimantes - ML-2950DR (10.94 mb)
Imprimantes - ML-2950ND (10.94 mb)
Imprimantes - ML-2950ND/GOV (10.94 mb)