Brady Co. Automatic Indentification Products CG Triumvirate is a trademark of Agfa Corporation. Corrupad is a Trademark of Corrupad Protective Packaging Inc. Bradyprinter THT Model 1024 is a Trademark of Brady USA Inc. As an Energy Star Partner, Brady USA Inc. has determined that this product meets the Energy Star guidelines for energy efficiency. Information in this document is subject to change without notice and does not represent a commitment on the part of Brady USA Inc. No part of this man

H. BRADY CO. AUTOMATIC IDENTIFICATION PRODUCTS Bradyprinte. T. TH. Mode. 200. an. 260. Therma. Transfe. Printe. USER'. GUID. Custome. par. #31450L-1. Manufacture. par. . 31450LB-1. Rev. . W. H. BRAD. CO. AUTOMATI. IDENTIFICATIO. PRODUCT. Proprietary Statement . This manual contains proprietary information of Brady USA, Inc. It is intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduce

Customer order # 11342L-12 Manufacturer part # 11342LB-12 Rev. 1 . This manual contains proprietary information of Brady Corporation. It is intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to any other parties for any other purpose without the expressed written permission of Brady Corporation. . Continuous improvement of products is a policy of Brady Corporat

A sample printout is shown in Figure 34 on page 81. NOTES on diagnostic printouts: • FE indicates a framing error. • OE indicates an overrun error. • PE indicates a parity error. • NE indicates noise. For any errors, check that your communication parameters are correct. Set the print width equal to or less than the label width used for the test. See page 46 for more information. Bradyprinter 200M-e and 200M-e 300 User’s Guide Selecting Prefix and Delimiter Characters Prefix and delimiter charact

PRINTER OVERVIEW General Features/Unique Characteristics .............................................................2 Operating Requirements .......................................................................................3 Label Dispensing/Print Requirements ...................................................................4 User Interface Controls .........................................................................................5 Sensors.........................................

These characters are available in fonts 1–6 and 9. Getting Started 13 _______________________________________________________________________ 14 Getting Started 2.4 Memory Cartridges The Printer has one standard memory cartridge slot. The primary use of the memory cartridges is for storing label formats, graphic images, fonts and for internal batch. Follow the instructions outlined below when installing memory cartridges. 1. Ensure that all printing has been completed. 2. Open the Side Access Co

At power up or in an idle condition, this value should be in the range of 060 to 065. A reading of 175 is high and could decrease the life of the printhead. An average amount of printing will give readings that range from 070 to 120. Pot -this reading comes from the darkness potentiometer located on the front panel board. It will vary from 000 (darkest) to 255 (lightest). Adjust this value for a midrange value of 128. TOFA -(Top of Form Adjustment) determines where the first position of print be

Default: Web Selections: Web, mark This parameter tells the printer whether you are using media with a web (gap/space between labels, notch, or hole) to indicate the separations between labels or if you are using media with a black mark printed on the back. If your media does not have black marks on the back, leave your printer at the default (web). PRINT METHOD Selecting Print Method Press the RIGHT BLACK OVAL key for the next value; press the LEFT BLACK OVAL key for the previous value. Default

(Fo. Serial-Interfac. Printer. Only. The M-Series Printer, with the RS-232 Serial Interface, uses eight miniature switches located on the rear of the printer, above the Signal Interface Cable Connector. The ON/OFF positions of these switches establish some of the Printer Configuration Parameters. Bank 1 switches must be properly positioned to establish serial data communications with the host computer. Thereafter, the position of these switches should not be changed. Note: Parallel-interface pri

±0.039" (±1.0mm) on noncontinuous media Horizontal . ±0.039" (±1.0mm) within a roll of media • Programmable print speeds: - 203 dpi models = 2.0" (51mm) through 10" (254mm) per second in 1" increments - 300 dpi model = 2.0" (51mm) through 6" (152mm) per second in 1" increments MVP Series Product Guide Page 18 Printer Specifications Media Specifications • Maximum label length: 39" (991mm) • Media type: continuous, die-cut, tags, black- mark • Media web width (label and liner): 1.0" (25.4mm) to 4.