Log:
Évaluations - 1, GPA: 4 ( )

Instructions Maytag, Modèle DFC1500

Fabricant : Maytag
Taille : 2.91 mb
Nom Fichier : 6ad6a7b1-a284-43f5-8990-d506fdb762da.pdf
Langue d'enseignement: enesfr
Aller à la télécharger



Facilité d'utilisation


• If the new disposer mounting is the same as old one, remove mounting assembly from disposer (Instruction 3) and go to Instruction 7. • If the new disposer mounting is different from the old one (or you wish to replace the old sink Steps 5 - 6 (below), and Instructions 2-5 (in previous column), then continue with Instruction 7. 5. Loosen three mounting screws, pry snap ring off with screwdriver, and remove old mounting assembly (see Figure 6-5). (Some mounting assembly removal requires additional tools.) 6. scrape all old putty from edge of sink hole. CLEAN SINK DRAIN LINE Failure to clean sink drain line may result in drain line blockage. 1. Remove P-trap. 2. With drain auger, clear away all hardened waste material in horizontal drain line. If you are not connecting a dishwasher to disposer, go to Instruction 9. PREPARE DISHWASHER DRAIN CONNECTION (IF APPLICA - BLE) The knockout drain plug should only be removed if you are connecting a built-in dishwasher to the disposer. NOTE: If the dishwasher connection is made without removing the plug, the Remove Knockout Plug 1. Lay disposer on its side and insert screwdriver into dishwasher inlet so tip rests on outer edge of knockout plug. 2. Tap end of screwdriver handle with hammer until molded plug breaks loose (see Figure 8-1). 3. REMOVE LOOSE KNOCKOUT PLUG FROM INSIDE DISPOSER. Attach Dishwasher Drain Connector If your dishwasher drain hose is 7/8" diameter, go to Instruction 9. If your dishwasher drain hose is not 7/8" diameter, you must attach a dishwasher drain connector to the dishwasher drain inlet. Follow the installation instructions with the connection kit. (You will connect the dishwasher drain hose to the connector in Instruction 12.) Electric Shock • Turn off electrical power at fuse box or circuit breaker before removing electrical cover plate. • Disposer must be grounded. Improper connection can result in electric shock. Personal Injury • Do not position your head or body under disposer; unit could fall during removal or installation. CHECK INSTALLATION DIMENSIONS A: Disposer Height B: Distance from bottom of sink bowl to centerline of discharge outlet. (Add 1/2" when stainless steel sink is used.) C: Distance from centerline of the discharge outlet to end of discharge tube. D: Disposer Width E: Distance from disposer vertical centerline to centerline of P-trap connection. F: Centerline of disposer discharge to centerline at waste pipe entering wall. (Dimension “F” must be greater than 1/4" to prevent standing water in disposer.) If replacing an existing disposer, skip ahead to Instruction 6. Instruction 2. DISCONNECT SINK DRAIN 1. Loosen nut (A) at top of “P-trap” with pipe wrench (see Figure 2-1). 2. Loosen nut (B) at top of extension pipe. Remove extension pipe. 3. lubricant.) 4. 5. DISASSEMBLE NEW DISPOSER MOUNTING ASSEMBLY 1. Insert wrenchette (or screwdriver) into one mounting lug and hold lower mounting ring securely with one hand (see Figure 3-1). With your other hand, turn mou...

Ce manuel est également adapté pour les modèles :
Autres appareils de cuisine - DFC5500 (2.91 mb)
Autres appareils de cuisine - DFC5500AAX (2.91 mb)
Autres appareils de cuisine - DFC6500 (2.91 mb)
Autres appareils de cuisine - DFC7500 (2.91 mb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories