Log:
Évaluations - 4, GPA: 4 ( )

Instructions Maytag, Modèle DFC5500AAX

Fabricant : Maytag
Taille : 2.91 mb
Nom Fichier :
Langue d'enseignement: enesfr
Aller à la télécharger



Facilité d'utilisation


• Disposer must be grounded. Improper connection can result in electric shock. Personal Injury • Do not position your head or body under disposer; unit could fall during removal or installation. CHECK INSTALLATION DIMENSIONS A: Disposer Height B: Distance from bottom of sink bowl to centerline of discharge outlet. (Add 1/2" when stainless steel sink is used.) C: Distance from centerline of the discharge outlet to end of discharge tube. D: Disposer Width E: Distance from disposer vertical centerline to centerline of P-trap connection. F: Centerline of disposer discharge to centerline at waste pipe entering wall. (Dimension “F” must be greater than 1/4" to prevent standing water in disposer.) If replacing an existing disposer, skip ahead to Instruction 6. Instruction 2. DISCONNECT SINK DRAIN 1. Loosen nut (A) at top of “P-trap” with pipe wrench (see Figure 2-1). 2. Loosen nut (B) at top of extension pipe. Remove extension pipe. 3. lubricant.) 4. 5. DISASSEMBLE NEW DISPOSER MOUNTING ASSEMBLY 1. Insert wrenchette (or screwdriver) into one mounting lug and hold lower mounting ring securely with one hand (see Figure 3-1). With your other hand, turn mounting assembly counterclockwise to remove mounting assembly from lower mounting ring. 2. Turn mounting assembly over (see Figure 3-2) and loosen three mounting screws (A) until you can access snap ring (B). 3. apart. INSTALL FLANGE IN SINK HOLE 1. Roll 1/4 pound (4 oz.) of non-hardening plumber’s putty to make 3/4" thick rope to seal 2. 3. to seat evenly on putty (see Figure 4-2). Use screwdriver or putty knife to scrape all putty from edge of sink hole. ATTACH UPPER MOUNTING ASSEMBLY TO SINK FLANGE 1. 2. seats against backup ring. 3. 4. Tighten three mounting screws up to sink until mounting assembly is seated tightly and evenly against sink. * help hold parts in place while installing snap ring. (Remember to remove rubber band after snap ring is installed.) If you are replacing an existing disposer, go to Instruction 6. Instruction 7. RETIRE EL TRITURADOR EXISTENTE 1. Desactive la corriente electrica en la caja de fusibles o el interruptor automatico. 2. Desconecte el sifon del tubo de descarga de desperdicios del triturador utilizando los alicates ajustables (ver Figura 6-1). (Tambien desconecte la conexion del drenaje de la maquina lavadora de platos, si se aplica). 3. Sostenga el triturador con una mano e inserte el extremo de la llave pequena o del destornillador en la parte derecha de una aleta de montaje en el anillo de montaje inferior (ver Figura 6-2). Levante ligeramente el triturador y suelte el anillo de montaje inferior empujando o halando la llave pequena o el destornillador hacia la izquierda, hasta que el triturador este separado del conjunto de montaje. (El triturador puede resultar pesado. Proporcione apoyo). 4. Teniendo la corriente electrica apagada, voltee el triturador y retire la placa de la cubierta electrica (ver Figura 6-3). Suelte el tornillo a tierra verde y retire las tuercas...

Ce manuel est également adapté pour les modèles :
Autres appareils de cuisine - DFC1500 (2.91 mb)
Autres appareils de cuisine - DFC5500 (2.91 mb)
Autres appareils de cuisine - DFC6500 (2.91 mb)
Autres appareils de cuisine - DFC7500 (2.91 mb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories