Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
Turn off the power supply. 10) Clean the storage bin liner and the storage bin cover using a neutral cleaner. Rinse thoroughly after cleaning. Replace the storage bin cover in its correct position. WARNING! CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place. Make sure that none have fallen into the storage bin. 11) Move the power switch to the "ON" position, then replace the front panel in its correct position. Turn on the power supply, then move the control switch to the "ICE" position to start the automatic icemaking process. I. Controls and Adjustments 1. Portion Control A variable resistor which controls the amount of ice dispensed is located on the control board. The figures on the label indicate dispensing time (sec.). See Fig. 8. When shipped, the portion control is set at the minimum dispensing time (0.6 sec.). DCM-750BAH(-OS); DCM-750BWH(-OS) . . . . . . . . . . . . Approximately 0.72 oz./0.6 sec. Approximate amount of ice dispensed per second. DCM-750BAH(-OS); DCM-750BWH(-OS) . . . . . . . . . . . . Approximately 1.2 oz./sec. 25 III. Cleaning and Maintenance WARNING CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after any cleaning or maintenance is done to the unit. Make sure that none have fallen into the storage bin. A. Cleaning and Sanitizing Instructions Hoshizaki recommends cleaning and sanitizing this unit at least twice a year. More frequent cleaning and sanitizing, however, may be required in some existing water conditions. WARNING 1. To prevent injury to individuals and damage to the icemaker, do not use ammonia type cleaners. 2. Carefully follow any instructions provided with the bottles of cleaning and sanitizing solution. 3. Always wear liquid-proof gloves and goggles to prevent the cleaning and sanitizing solutions from coming into contact with skin or eyes. 4. After cleaning and sanitizing, do not use ice made from the cleaning and sanitizing solutions. Be careful not to leave any solution on the parts or in the storage bin. Fig. 9 Spout B Extruding Head Spout A Agitating Motors Dispensing Motor Agitators Dispensing Auger Power Switch Control Switch Dispense Mode Switch Reservoir Bin Control Assembly Storage Bin Cover Spout Cover Evaporator Assembly Safety Switch Optical Sensors (-OS) Float Switch Ice Guide Drain Pipe Holder Drain Pipe 1. Water System a) Cleaning Solution Dilute 9.6 fl. oz. (0.29 l) of Hoshizaki "Scale Away" with 1.6 gal. (6.0 l) of warm water. b) Cleaning Procedure 1) Close the icemaker water supply line shut-off valve. 2) Move the control switch to the "DRAIN" position and allow the water system to drain for 5 minutes. Note: If the unit is running, the drain valve will not open until 2.5 minutes after the control switch is moved to the "DRAIN" position. This allows the components to cycle down. 3) Move the dispense mode switch to the "CONTINUOUS" position, then dispense all of the ice from the storage bin. 4) Move the control switch to the "OFF" position, then turn off the power supply. Remove the front and top panels, then move the power switch to the "OFF" position. 5) Remove the storage bin cover. Remove spout B, then remove spout A. See Fig. 9. 6) Pour the cleaning solution over the extruding head until the evaporator assembly and the reservoir are full and the solution starts to overflow into the drain pan. Note: If there is excess scale on the extruding head, fill the evaporator assembly and reservoir as described above, then use a clamp on the reservoir hose between the reservoir and evaporator assembly to block flow. Pour additional cleaning solution over the extruding head until the evaporator assembly is completely full. 7) Replace spout A, spout B, and the storage bin cover in their correct positions. 8) Allow the icemaker to sit for 10 minutes before operation. If you placed a clamp on the reservoir hose in step 6, remove it before operation. 9) In bad or severe water conditions, clean the float switch assembly as described below. See Fig. 9. Otherwise, continue to step 10. a. Remove the float switch assembly from the reservoir cover. b. Wipe down the float switch assembly with the cleaning solution. c. Rinse the float switch assembly thoroughly with clean water. d. Replace the float switch assembly in its correct position. 10) Move the power switch to the "ON" position and replace the panels in their correct positions. Turn on the power supply, then move the control switch to the "ICE" position. Make ice using the solution until the icemaker stops making ice. Note: This unit will not run if the safety switch is not engaged. 11) Move the control switch to the "DRAIN" position and allow the solution to drain for 5 minutes. 12) Move the control switch to the "ICE" position. Open the icemaker water supply line shut-off valve to supply water to the reservoir. 26 13) After the gear motor starts, move the control switch to the "DRAIN" position and allow the water system to drain for...
Ce manuel est également adapté pour les modèles :Autres appareils de cuisine - DCM-750BWH(-OS) (2.11 mb)