Évaluations - 2, GPA: 5
(
)
)
|
Facilité d'utilisation
A. Disassemble the sink flange assembly from the disposer by turning the mount ring to the left (clockwise) and removing it. B. Raise the mount ring toward the top of the sink flange. Remove the cushion mount and the mount ring. You may want to practice installing the cushion mount at this point before you are under the sink. C. Unscrew the support ring from the sink flange and remove the fiber gasket. You are now left with the sink flange and the rubber gasket. D. The rubber gasket is used instead of plumbers putty with stainless steel sinks. E. If no putty is used, insert the sink flange through the rubber gasket into the sink opening. Do not turn the flange once it is seated. F. If you use putty instead of the gasket, form a ring around the underside of the sink flange. Insert the flange into the sink opening, press down hard to squeeze out excess putty. From under the sink, trim off excess putty flush with the bottom edge of the sink opening. Use putty sparingly on cast iron sinks. G.From underneath the sink, slip the fiber gasket onto the exposed sink flange. With arrows pointing up, screw the support ring onto the sink flange and hand tighten until Hand-tighten sink flange the sink flange will not move. At this point you may want to insert the stopper in the sink and fill with water to check the sink flange seal and insure there are no leaks. H.Place the mount ring over the sink flange and hold in place while installing the cushion mount (large side down). Make sure the groove on the inside of the cushion mount fits over the lip on the sink flange, Cushion Mount Detail similar to putting the lid Top Groove on a plastic container. Run your fingers Bottom around the entire Bead cushion mount with slight pressure. Do not press too hard. When the cushion mount is properly seated, the mount ring can be pulled downward over the cushion mount and will be free to turn. Installation Instructions DISHWASHER CONNECTION (IF REQUIRED) If you are connecting to a dishwasher, complete the following step. If a dishwasher is not to be connected, go on to “Attaching the Discharge Elbow” section. KNOCK OUT PLUG Using a blunt instrument (steel punch or wooden dowel), knock out entire plug. Do not use a screwdriver or sharp instrument. When knockout plug falls into disposer, you may remove it or simply grind it up when the disposer is used. This will not damage the disposer in any way, but may take some time to grind, over the course of several uses. 1 Connect the dishwasher hose using a hose clamp. If the hose size is different, you will need a stepped rubber adapter. CONNECT HOSE2 Knock out plug Hose Clamp Stepped Rubber Adapter CONNECT DISCHARGE ELBOW Connect the discharge elbow to the disposer.* Make sure all plumbing connections are tight. ATTACHING THE DISCHARGE ELBOW 3 Rubber Gasket Discharge Elbow * Some installations (see page 8 for examples) may require the use of a flexible drain pipe. Installation Instructions 4 CONNECTING DISPOSER TO SINK FLANGE LOCK MOUNT RING Turn the mount ring slowly to the right until it locks up tight. Hopper projections must be to the extreme left of the mounting slots. If the mount ring is hard to turn, you may add a small amount of petroleum jelly or liquid soap to the hopper projection. Run water and check for leaks. 3 Hopper Projection in “Supported” Position Hopper Projection in “Locked” Position Mount Ring Locking Detail Check the unit for leaks 24 hours after installation and first operation. CHECK FOR LEAKS4 Line up the disposer under the sink flange. Guide the hopper projections into the mount ring slots. Turn the mount ring about 1/4. to the right so that the disposer is temporarily supported. 1 Turn the mount ring and the disposer until the disposer discharge elbow lines up with the outlet pipe (see page 8). LINE UP WITH OUTLET PIPE2 Mount Ring Slot Hopper Projection Discharge Elbow Outlet Pipe ATTACH TO SINK FLANGE Mounting Slot Installation Instructions DIMENSIONS GFC320 Model Series 63/16” 5 3/16” 1211/16” 41/2” 11/2” 53/8” GFC520 Model Series GFC530 Model Series GFC720 Model Series GFC1020 Model Series 11/2” 11/2” 11/2” 59/16” 7 1/4” 8 1/2” 161/16” 71/4” 8 1/2” 5 9/16” 141/2” 615/16” 53/8” 73/4” 137/16” 4 1/2” 4 1/2” 4 1/2” GFB760 Model Series Batch Feed O...
Ce manuel est également adapté pour les modèles :Autres appareils de cuisine - GFB760 (466.78 kb)
Autres appareils de cuisine - GFC1020 (466.78 kb)
Autres appareils de cuisine - GFC320 (466.78 kb)
Autres appareils de cuisine - GFC520 (466.78 kb)