Évaluations - 3, GPA: 4 ( )

Fabricant : Black & Decker Taille : 5.28 mb Nom Fichier : Langue d'enseignement:

4. After measuring the overhang molding thickness as shown in Illustration G, look at the dashed lines on the mounting template; each line has a measurement next to it that indicates the thickness of the overhang molding used with that line. For example, if your cabinet has an overhang molding thickness of .”, you will use the .” dashed line on the template. 5. Fold the template along the dashed line that matches the thickness of your overhang molding. 6. Place the folded template against the back edge of the overhang molding, making sure the side with the drill hole marks is facing down (H). Important: Do not align screw holes on template directly under the partition between cabinets, as this will prevent you from installing the appliance properly. Pay close attention to where the drill holes will be set so as not to damage your cabinets during mounting. Drilling through your cabinet’s partition may cause damage to cabinets and prevent proper installation. 7. Making sure to keep the fold line straight against the back edge of the overhang molding, tape the template securely in place. 8. Drilling from under the cabinet up, drill holes through the 4 places marked on the template using a .-inch drill bit (J). Important: Always ensure you are drilling straight up through the marked mounting holes on the template. Drilling at an angle may prevent proper installation and may damage cabinets if the drill bit pierces the partition. 9. Once holes are drilled, remove tape and mounting template. 10. Wipe dust and debris off the underside and topside of the cabinet surface. 11. Place a washer inside the cabinet over each of the 4 holes you drilled. F G H J 12. Now, use your ruler or the paper ruler provided to measure the overhang molding height, placing your ruler vertically against the underside of the cabinet behind the overhang molding. This number determines the number of spacers you need, using a number of spacers equal to the overhang molding height. For example, a 1” overhang molding would use 2, .” spacers on each of the rear holes (K). 13. Drop one of your screws through each of the washers covering the holes in the cabinet, from inside the cabinet down. Note: To determine which screws to use, you must have enough of the screw exposed underneath the cabinet to properly thread the screw into the nut. 14. Place the appropriate number of spacers determined in step 12 on both of the rear screws to ensure the appliance will be even (L). Note: If the height of your overhang molding is too tall to be accommodated by the number of spacers provided, you may call, toll-free, at 1-800-231-9786 to order additional spacers at no charge. Note: For spacer installation, you may require assistance in mounting in order to hold spacers in place while securing the appliance at the same time. If assistance is not available, use a small clamp to hold the spacers in place while you position the appliance. 15. Once spacers are set, hold appliance up and tighten screws to secure. Screw from inside the cabinet down. Note: Always tighten screws to ensure the appliance does not move or shake during operation. 16. Pull out cord from cord storage behind appliance and plug into standard electrical outlet. Extra cord can be fed back into storage or hung over cord management hook behind unit (see illustration F). Note: If you are connecting this appliance to the receptacle of another †SpaceMaker™ appliance such as the toaster oven or coffeemaker, make sure you can easily unplug the appliance following use. 17. Your †SpaceMaker™ appliance is now ready for use! K L How to Use This appliance is for household use only. OPENING A CAN 1. Lift piercing lever. 2. Tip can so that the rim is under the locating post, then push down on the piercing lever, making sure the cutter blade is inside the rim of the can (M). Note: Because of the hands-free feature, it is not necessary to hold the lever down or hold the can during cutting. However, you may have to support very tall or heavy cans. Tip: When the can is opened, the can opener will stop automatically. 3. To remove the can, hold it with one hand and raise the lever with the other. Caution: Avoid contact with the cut edges of the can or lids — they are sharp. During opening process, the design of your can opener will roll the rim of the can to prevent sharp edges; however, handle with caution and always handle cut lid with caution, as these edges are not rolled. 4. Carefully discard the lid from the magnet. Important Tips: • Do not use this can opener to open cans w...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :