To test the GFCI breaker follow these instructions (spa should be operating): Press the TEST button on the GFCI. The GFCI will trip and the spa will 1. shut off. Reset the GFCI breaker by switching the breaker to the full OFF posi2. tion, wait a moment, then turn the breaker back on. The spa should have power again. Configuring the 6300 Control System The 6300 control system requires higher power than other 240V systems. Dip switch #10 is factory set in the ON position. This causes the heater to

All rights reserved. Duplication without written consent is strictly prohibited. Cal Spas® is a registered trademark. Due to continuous improvement programs, all models, operation, and/or specifications are subject to change without prior notice. LTR20091024, Rev. A 12/15/08 CONTACT INFORMATION For customer service, please contact your authorized dealer immediately. If you need additional information and/or assistance, please contact: LMS Customer Service Department 1462 East Ninth Street Pomona

The sand bed is to level the spa shell and provide a perfect support base with no voids when the spa is lowered into the hole. Your excavation should be approximately one foot longer and one foot wider than the spa shell. This will allow for a six inch over dig all the way around the spa once it is in place. Additional hand excavation will be required to insure the skimmer will fit in the excavation when attached to the spa. Sand or rock dust must be used to bed the shell into the excavation and

If you are installing your spa with any type of structure on the outside, such as a gazebo, remember to allow access for service. It is always best to design special installations so that the spa can still be accessed. Outdoor equipment pack (in-ground spas only) The Designer Spa series requires an external equipment pack. When locating the outdoor equipment pack, you will want to consider the following: The equipment pack must be located within a maximum of 15 feet • from the spa. Ensure the eq

Designer Spa Specifications DIJ401 and DIJ405: Equipment pack weight = 250 lbs. DIJ407: Equipment pack weight = 300 lbs. 2.5 HP heat pump 4 HP swim pump Note: Equipment pack cannot exceed 15 feet from spa. In-Ground Plumbing Connections IMPORTANT! Always check local codes prior to any in-ground spa installation. Once the spa and equipment are properly located, you will want to lay out the plumbing run. Trenches should be deep and wide enough to allow all pipes to be buried below the frost line a

If you are pouring a regular deck up to the spas coping, then the top of the coping should be 4” above the surrounding area. In either event, it is recommended to dig out an area around the spa exposing the flange of the coping and just under it. This is important, as concrete should be packed under and over the flange of the spa, as the deck is poured. This will lock the spa into the concrete and provide for a much stronger bond of the spa to the deck. It will also eliminate cracking of the dec

Topside Control Panel and Temp Sensor: 1” line that connects to the bottom of the control box located on the equipment pack. Electrical and Electronic Connection Remote Equipment Topside Control Panel The next few steps to complete the installation should be performed along with installation of the temperature sensor and 12V spa light wiring (if applicable). All of these components are generally installed using the same conduit. Locate the topside control panel 1. extension loom in the control b

If you are installing a spa or villa on an elevated • wood deck or other structure, we strongly recommend that you consult a structural engineer or contractor to ensure the structure will support the weight of 150 Lbs./ sq. ft. It is strongly recommended that a qualified, • licensed contractor prepare the foundation for your villa. Size Specifications Length Width 12’ 12’ 12’ 16’ 14’ 14’ 14’ 18’ 16’ 16’ NOTE: We recommend that the foundation extend beyond the dimension of the villa. For example,

• Do not use the sauna after recovering from a long or serious illness or if you are physically exhausted or feeling weak. • When using the sauna for the very first time, start at a low temperature and slowly increase the temperature as you become accustomed to sauna heat. Do not force your body to endure uncomfortable heat. over time and several sauna exposures, your body will acclimate to higher temperatures. Take it slowly! • Stay in the sauna for about 10 to 15 minutes, step out and cool off

Available in both straight and corner configurations with seating for 1 to 4 adults, there is an Infrared model for every indoor configuration. Usage: Heating Type: Configurations: Seats: Usage: Heating Type: Configurations: Seats: Usage: Heating Type: Configurations: Seats: Usage: Heating Type: Configurations: Seats: Outdoor Steam In-Line Up to 5 Indoor Steam In-Line & Corner Up to 4 Indoor Carbon Fiber In-Line & Corner Up to 4 Indoor Infrared In-Line & Corner Up to 4 WWW . CA l S p AS . C om 2