Évaluations - 3, GPA: 3.3
(
)
)
|
Facilité d'utilisation
WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body. WARNING: Always use eye protection. All users and bystanders must wear eye protection that conforms to ANSI Z87.1. WARNING: Always wear proper personal hearing protection that conforms to ANSI S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss. • The label on your tool may include the following symbols. The symbols and their definitions are as follows: V ........................volts A .......................amperes Hz ......................hertz W ......................watts min ....................minutes .................... alternating current .................direct current .................... alternating or direct current ......................Class I Construction no.....................no load speed (grounded) ..................... earthing terminal ......................Class II Construction ..................... safety alert symbol (double insulated) BPM ................. beats per minute …/min ...............per minute RPM .................revolutions per minute Motor Your DEWALT tool is powered by a DEWALT-built motor. Be sure your power supply agrees with the nameplate markings. Voltage decrease of more than 10% will cause loss of power and overheating. All DEWALT tools are factory tested. COMPONENTS (Fig. 1) WARNING: Never modify the power tool or any part of it. Damage or personal injury could result. A. Variable speed trigger switch G. Mode selector B. Main handle H. Reversing lever C. Side handle I. Lock-on button D. Depth rod (D25012, D25013 only) E. SDS Plus® chuck J. Depth rod release button F. Mode selector button INTENDED USE These heavy-duty rotary hammers have been designed for professional drilling and hammerdrilling, screwdriving and light chipping at various work sites (i.e., construction sites). DO NOT use under wet conditions or in presence of flammable liquids or gases. These heavy-duty rotary hammers are professional power tools. DO NOT let children come into contact with the tool. Supervision is required when inexperienced operators use this tool. Side Handle (Fig. 1) WARNING: To reduce the risk of personal injury, ALWAYS operate the tool with the side handle properly installed and securely tightened. Failure to do so may result in the side handle slipping during tool operation and subsequent loss of control. Hold tool with both hands to maximize control. A side handle comes assembled with this rotary hammer. The side handle (C) can be fitted to suit both right-hand and left-hand users. TO ADJUST THE SIDE HANDLE 1. Loosen the side handle (C) by turning it counterclockwise. 2. Rotate the side handle to the desired position. 3. Tighten the side handle by turning it clockwise. TO CHANGE SIDES For right-hand users: slide the side handle clamp over the chuck, handle at the left. For left-hand users: slide the side handle clamp over the chuck, handle at the right. Trigger Switch (Fig. 1) To start the rotary hammer, depress the trigger switch (A). To stop rotary hammer, release the switch. NOTE: Use lower speeds for starting holes without a centerpunch, drilling in metal, plastics or ceramics, or driving screws. Higher speeds are better for drilling in masonry for maximum efficiency. VARIABLE SPEED The variable speed trigger switch (A) permits speed control. The farther the trigger switch is depressed, the higher the speed of the drill. LOCK-ON BUTTON (D25012, D25013 ONLY) WARNING: Be sure to release the locking mechanism before disconnecting the plug from the power supply. Failure to do so will cause the hammerdrill to start immediately the next time it is plugged in. Damage or personal injury could result. The lock-on button (I) is for use only when the rotary hammer is stationary, mounted in a drill press stand or for chipping applications. Before using the tool each time, be sure that the lock-on button release mechanism is working freely. For continuous operation, press and hold the trigger switch (A); press the lock-on button (I); release the trigger switch and then release the lock-on button. The tool will continue to run. To stop the tool in continuous operation, quickly press and release the trigger switch. Reversing Lever (Fig. 1) The reversing lever (H) is used to reverse the rotary hammer for backing out fasteners or jammed bits in drill-only mode. CAUTION: When reversing to clear jammed bits, be ready for strong reactive torque. To reverse the rotary hammer, turn it off and align the reversing lever (H) with the yellow arrow pointing backward (viewed when holding drill in operating position). To position the lever for forward operation, turn the rotary hammer off and align the reversing lever (H) with the yellow arrow pointing forward (viewed w...
Ce manuel est également adapté pour les modèles :Autres outils - Compact SDS Plus N027959 (1.7 mb)
Autres outils - Compact SDS Plus D25012 (1.7 mb)