5 facing up, and attaching the legs in that position. NOTE: Before using the alternate set-up, remove the 5/16" hex head screws from holes (B) Fig. 6 in the motor/blower assembly and place them in the holes (C). Air will leak if the screws are left out of these holes. ATTACHING THE DUST INTAKE PORTS Disconnect the machine from the power source! AWARNING Place the dust intake port (A) Fig. 7 over the intake hole (B) opposite the motor. Align the four holes (C) (two of which are shown) in th

Main Street 714-641-0529 Fax: 714-641-2947 Santa Barbara 93101 Buena Tool Co. 433 Laguna Street 805-963-3885 Santa Rosa 95401 Acme Electric Tool Repair 742 Wilson Street 707-546-5862 Santa Rosa 95403 H & V Tool Repair 1808 Empire Industrial Court #D 707-528-1111 Simi Valley 93065 Simi Tool Repair 1236 Los Angeles Avenue, UnHD 805-584-8138 Temecula 92390-5623 California Electric Service 41715 Enterprise Circle North 909-695-5445 Torrence 90502 Universal Tool Service 21804 S. Vermo

22 Fig. 23 OPERATING CONTROLS & ADJUSTMENTS WARNING: FOR OPERATOR SAFETY, MAKE CERTAIN THE DUST INTAKE PORT IS COVERED WITH THE VACUUM HOSE BEFORE OPERATING THE MACHINE. THE ROTATING FAN INSIDE THE BLOWER HOUSING IS ACCESSIBLE THROUGH THE DUST INTAKE PORT AND IS HAZARDOUS. MAKE SURE INTAKE CAP COVERS THE INTAKE PORT WHEN HOSE IS REMOVED. ALWAYS WEAR PROPER APPAREL.DO NOT WEAR JEWELRY, AND KEEP FINGERS AND ALL FOREIGN OBJECTS OUT OF THE DUST INTAKE PORT.ALWAYS FOLLOW THE SAFETY RULES OF THIS MANU

460 VOLT OPERATION 460 volt operation of the 50-764 requires replacement of the motor starter and reconfiguration of the motor's internal connections. A 460 volt starter is available from most industrial electrical supply dealers and must be installed by a qualified electrician. DO NOT ATTEMPT to wire the machine for 460 volts without replacing the starter. Doing so will cause damage to the machine and personal injury could result. FUNCTIONAL DESCRIPTION FOREWORD The Delta Industrial Models 50-7

The fan should rotate clockwise. You can reverse the rotation of the motor by interchanging any two of the three incoming power lines connected to terminals (C) Fig. 16. Disconnect the machine from the power source before reversing the wires. ADANGER 460 VOLT OPERATION 460V operation of the 50-762 requires replacement of the motor starter and reconfiguration of the motor's internal connections. This item is available from most industrial electrical supply dealers and must be installed by a q

In a severe dirty operation, the blower impeller should be cleaned with a wire brush to prevent an accumulation of foreign matter that could result in blower unbalance After cleaning impeller, inspect for possible cracks or excessive wear, which can cause unbalance. DO NOT USE AN IMPELLER THAT IS CRACKED OR EXCESSIVELY WORN; REPLACE IT WITH A NEW IMPELLER. MOTOR MAINTENANCE: Removing dust and dirt: Blow off motor with low pressure air to remove dust or dirt. Air pressure above 50 P.S.I. shou

The smaller the gauge number, the heavier the cord. 15. SECURE THE WORKPIECE. Use clamps or a vise to hold the workpiece when practical. Loss of control of a workpiece can cause injury. 16. FEED THE WORKPIECE AGAINST THE DIRECTION OF THE ROTATION OF THE BLADE, CUTTER, OR ABRASIVE SURFACE. Feeding it from the other direction will cause the workpiece to be thrown out at high speed. 17. DON’T FORCE THE WORKPIECE ON THE MACHINE. Damage to the machine and/or injury may result. 18. DON’T OVERREACH. Lo

4. Thread hex nut (B) Fig. 4 onto each of the four bolts and tighten securely. ASSEMBLING SIDE SUPPORTS 1. Place the dust collector base (A) Fig. 5, in an upright position as shown. 2. Align the two holes in the bottom of side support (B) Fig. 5 with the two holes (A) in the base. 3. Insert a 5/16-18x3/4" hex head screw (A) Fig. 6 thru each hole in the side support and base. 4. Place a 5/16" lockwasher onto the hex head screw. 5. Thread a 5/16" hex nut onto the hex head screw and tighten securel

14A, with the two holes in the drum. Insert a 1/4-20x5/8" hex head screw through the holes in the retaining clip and the holes in the drum. Place a 1/4" flat washer onto the screws, and thread 1/4-20 hex nut s on the screws and tighten securely. Repeat this process for the three remaining sides of the drum. A B Fig. 14A A B C Fig. 15 ASSEMBLING DUST INTAKE PORT AND CAPS TO BLOWER AND MOTOR ASSEMBLY 1. MAKE CERTAIN THE DUST COLLECTOR IS DISCONNECTED FROM THE POWER SOURCE. 2. Align the four holes

Cutters 09-128 & 09-137 are counterbored to fit Stub Spindle. Cutters are shown 3/8 size. 1/2 Lb. each. 09-100 09-101 09-102 09-103 09-106 1/2" Cove 5/16" Cove 1/8" & 3/8" 1/4" & 1/2" 90° 5/16" Qr. Rd. 3/8" Bead Qr. Rd. Qr. Rd. V-Groove 1/4" Bead 09-109 09-111 09-112 09-113 09-114 1/4" Flute Stile with Rail with Drop Leaf Drop Leave 1/4" Groove 1/4" Tongue Bead Cove 09-115 09-116 09-117 09-118 3-Bead Clover 1/2" Rad. 3/4" Qr. Rd. Cove Leaf Base Shoe 09-120 09-121 09-125 09-126 09-128 Ogee Female