Évaluations - 4, GPA: 4 ( )

Fabricant : Pioneer Taille : 3.17 mb Nom Fichier : Langue d'enseignement:

• Automatically selects the convergence memory as follows. For NTSC input:MEMORY 1 For PAL input:MEMORY 2 Horizontal frequency 20 kHz to 28 kHz input:MEMORY 3 Horizontal frequency 28 kHz to 35 kHz input :MEMORY 4 When TV SYSTEM=NTSC • The convergence memory is always set to MEMORY 1 regardless of the input signal. When TV SYSTEM=PAL • The convergence memory is always set to MEMORY 2 regardless of the input signal. In standard settings, MEMORIES 1 to 4 are selected as described above, but MEMORIES 5 to 7 can be selected if preset using the remote control or commands of the Personal Computer. When the input signal is NTSC only or PAL only, by setting the TV SYSTEM to NTSC or PAL, smooth input switching (no image distortion) will be possible. Normally, no problems will be encountered with the above method. But if two or more types of signals are input to the same input function, convergence adjustment has to be performed according to the respective input source. (For example, when there is signal phase difference in each input source, when connecting several PCs and switching from outside, etc.). In such cases, use convergence adjustment memories 5 to 7 (MANUAL 1 to 3). The 5 to 7 convergence adjustment memories can be switched from outside using the Personal Computer. Finally, examples of main uses by the system of these units are provided below. For details of how to set the convergence memory (specific example), refer to ”3. Examples of Main Uses of Cube System”. ADJUSTMENTS (3) White Balance Adjustment Memory ADJUSTMENTS has altogether six white balance adjustment memories. Color mode 1 (Normal) VIDEO, Y/C input memory RGB input memory Factory shipment memory Color mode 2 (Re-expose) VIDEO, Y/C input memory RGB input memory Factory shipment memory Four memories can be actually adjusted except the factory shipment memory. The factory shipment memory contains the normal white balance adjustment data and re-expose white balance adjustment data. By setting to color mode 1 using the rear panel switch, etc., the white balance adjustment data can be switched by synchronizing with input switching. This is the same for color mode 2. If it is necessary to change color modes 1 and 2 using the input function, connect the PC and switch each time it is necessary. (4) Combined Use of Remote Control and Personal Computer Although it is possible to connect both the remote control (RU-V107) and Personal Computer, adjustments cannot be performed using both at the same time. Remote control, Personal Computer commands and rear panel switches operated the latest are given priority. When the adjustment mode is set by the Personal Computer while adjusting with the remote control, the adjustment mode will be set by the Personal Computer, disabling adjustments to be performed using the remote control. If the adjustment mode is set by the remote control using adjustments by the Personal Computer, adjustments by the Personal Computer will be disabled. Furthermore, if the rear panel switches are operated when the adjustment mode is set by the remote control or Personal Computer, the adjustment mode is exited and the rear panel switches operations are started. (5) Memory of Adjustment Data and Settings When adjustments are ended in the adjustment mode such as convergence, white balance, etc., always exit the adjustment mode (AJN for Personal Computer, ADJ OUT key for remote control). If the power is turned off (AC OFF) without exiting the adjustment mode, a part of the adjustment data will not be preserved in the memory. The input function, MULTI ON/OFF (peripheral light amount switching), COMBINATION ON/OFF (ABL link switching), COLOR MODE 1/2 (white balance switching), TV SYSTEM setting, and convergence memory state setting will be preserved in the memory only when the power is turned off using the remote control, command of a Personal Computer (POF) or the rear panel tact switch. The AC ON/OFF will not allow data to be preserved in the memory.) When starting or stopping the system by AC ON/OFF in an installation condition for demonstration, use this method to preserve the conditions in the memory first. ADJUSTMENTS (6) Giving IDs When several Multi projection units are used to compose the 9 screens or 16 screens (multi-screen), the ID is used to differentiate between Multi projection units. When the units are given IDs, by connecting the ABL link cable, commands can be transmitted by specifying the ID, and it is possible to operate only Multi projection unit corresponding to that ID by remote control operations. Commands: IDC (IDC CLEAR) ;Clears the ID given IDS (ID SET) ;Gives an ID The IDS is valid only when no ID has been given. It will be valid from units nearest to the personal computer (remote control). (Example) 4 screens • When giving IDs first using Personal Computer. Personal Computer Multi Projection Unit Multi Projection Unit Multi Projection Unit Multi Projection Unit ID=...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :