Évaluations - , GPA: ( )

Instructions Sanyo, Modèle AH-23541

Fabricant : Sanyo
Taille : 455.2 kb
Nom Fichier :

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Remove the protective caps (front and back) on the lens. 2. Insert the lens into the Lens Bracket of the projector asmatching the red mark on the lens to that on the LensBracket. 2 -2Fig- 2 Red mark 3. Slowly turn the lens clockwise until it clicks. Make sure thatthe lens is fully inserted to the projector. Lens Replacement Procedure (For B type Cabinet) (For B type Cabinet) Perform the steps 1-6 for lens replacement. First set the lens at the lowest position with lens shift adjustment. 1 Remove the Lens Cover and the Top Cabinet 1. Turn the Lens Cover counter-clockwise and pull ittoward front to remove the Lens Cover. 2. Remove the two screws (SCREW "A") and removethe Top Cabinet. 1. Pull Lens Cover toward front and remove it. 2. Remove the two screws (SCREW "A") and removethe Top Cabinet. Slide the Light-Block Sheet Base upward to remove it. 2 Remove the Light-Block Sheet Base SCREW "A" LENS COVER TOP CABINET Fig-1-1 SCREW "A" LENS COVER TOP CABINET Fig-1-2 -3Fig- 2 LIGHT-BLOCK SHEET BASE 3 Remove the Lens 3 Remove the Lens Fig-3 LENS LOCK LEVER 4 Fig-4 Insert the lens into the Lens Bracket as matching these marks. LENS BRACKET -4 5 5 Mount the Light-Block Sheet Base Mount the Light-Block Sheet Base. LIGHT-BLOCK SHEET BASE LIGHT-BLOCK SHEET Fig-5 Light-Block Sheet should belocated under the hooks. HOOKS HOOKS 6 Mount the Top Cabinet and the Lens Cover For the Cabinet Fig. 6-1 1. Mount the Top Cabinet with 2 screws. 2. Mount the Lens Cover. Position the mark "UP" of the Lens Cover on top andpush into the cabinet. Turn the Lens Coverclockwise until it is securely locked. {When LNS-W11 (AH-23631) is installed, the LensCover is unnecessary.} For the Cabinet Fig. 6-2 1. Mount the top cabinet with 2 screws. 2. Push into the Lens Cover to the Top Cabinet. Confirm the top and bottom of the lens cover. The part circled in Fig-6-2 should be fitted. {When LNS-W11 (AH-23631) is installed, the LensCover is unnecessary.} Turn the projector on and check Lens shift, Zoom and Focus is operating properly. If Light-Block Sheet interfere with those operations, check if the Light-Block Sheet is set properly. LNS-W11 (AH-23631) cannot adjust the Zoom and Focus at the Remote control or the projector. UP Fig-6-1 Fig-6-2 -5 Focus Adjustment {For LNS-W11 (AH-23631)} Set up the projector in the place where it is to be used, turn on the power and project a picture. Adjust the position of the projector to suit the projection position. 1. Turn the focus ring to adjust the focus at the center of the screen. The focus at the edges of the screen may not be as sharp as at the center of the screen. 2. If the focus cannot be set correctly at the center of the screen, it will be necessary to move the lens unit forward or back relative to the flange in order to adjust the back focus. Carry out this adjustment according to the procedure given below. a. Turn the fixing roulette about 1/4 of a turn counterclockwise to release it. The roulette can be released more easily if you place t...