Log:
Téléchargements : 1   Taille : 4 mb   Fabricant : Omnimount  
Catégorie : Projecteurs

Téléchargements : 9   Taille : 4 mb   Fabricant : Omnimount  
Catégorie : Projecteurs

Téléchargements : 8   Taille : 1017 kb   Fabricant : Omnimount  
Catégorie : Projecteurs
@name

TPUM-1: Tilting Pipe Adapter B. A. To adjust tilt 1. Hold A with 3/ 4” Socket 2. Loosen B with 3/ 4” Socket 3. Loosen C with 9/ 16” Socket 4. Position Display 5. Tighten A,B, & C • Designed for 26” - 55” Flat Panel • Maximum Weight Capacity: 175 • Connects to 1.5” NPT Pipe Specifications are subject to change without prior notice. Every effort has been made to provide accurate and error-free assembly and installation. Omni- Mount Systems disclaims liability for any difficulties arising from the

Téléchargements : 8   Taille : 353 kb   Fabricant : Omnimount  
Catégorie : Projecteurs
@name

Note: Orient the cable management port on the pipe drop assembly so that it faces the projector cable drop. Extended Ceiling Mount For installations that require a ceiling drop in excess of 18”, standard 1 .” pipe may be used to extend the standard pipe drop assembly. Pipe extension should be cut to the required additional length, threaded on both ends, and then attached to the standard pipe drop assembly with a pipe coupler (not supplied). Note: Orient the cable management port on the pipe drop

Téléchargements : 8   Taille : 353 kb   Fabricant : Omnimount  
Catégorie : Projecteurs
@name

6 Determine required mounting screw size ( 4, 5 or 6 mm) for projector. Note: Consult projectors owners’ manual for screw sizes and mounting holes. Lay projector on table with mounting surface face up. Place grid section of bottom projector mounting plate onto top of projector in desired mounting orientation (horizontal or vertical). (Fig. 6) Using a pencil or felt tipped pen, mark the locations of the projectors threaded inserts onto the grid for refer- Part Projector Mounting Hardware Qty. Bag

Téléchargements : 13   Taille : 353 kb   Fabricant : Omnimount  
Catégorie : Projecteurs
@name

Every effort has been made to provide accurate and error- free assembly and installation. OmniMount Systems disclaims liability for any difficulties arising from the interpretation of information contained in these instructions. If OmniMount products are used for purposes other than their original intent, OmniMount, its distributors and retailers shall not be held responsible or liable for injuries or property damage, direct, indirect, or consequential, which may arise from the inability to use

Téléchargements : 0   Taille : 211 kb   Fabricant : Omnimount  
Catégorie : Projecteurs

Téléchargements : 13   Taille : 172 kb   Fabricant : Omnimount  
Catégorie : Projecteurs

Téléchargements : 4   Taille : 172 kb   Fabricant : Omnimount  
Catégorie : Projecteurs

Téléchargements : 28   Taille : 160 kb   Fabricant : Omnimount  
Catégorie : Projecteurs
@name

PFC-A (Female to Female Coupler) OMNI (Not Included) PFC Coupler 1 r 1 - fl V_!-■ <»-^P-A NPT pipes Available Sizes 12", 18", 24" (Not Included) (Not Included) Pouch # Part # Description Qty 1 COUPLER (PMD Series Compatible) 1 1 P-A SCREW 1/4 inch L 3/8 inch 4 1 P-B ALLEN KEY M4 1





catégories