Log:
Évaluations - 3, GPA: 4 ( )

Instructions Chamberlain, Modèle NLS1

Fabricant : Chamberlain
Taille : 1.06 mb
Nom Fichier : 8f71b71b-4b9c-4cea-aeaf-b7e14d4c6c45.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


Volume: Pressing the Volume DOWN button will lower the volume and pressing the Volume UP button will increase the volume. Intercom Models NLS1 & NLS1C (1) NLS2 & NLS2C (2) Rubber Pads Models NLS1 & NLS1C (1) NLS2 & NLS2C (2) MONITOR HOLD OFF 1 3 2 4 VOLUME TAL K ACTIVE Operation & Features Channel Select Button: Press the Channel Select button to set intercom to one of four secure channels or the paging channel. The default channel for the intercom is the paging channel where all four channel lights are lit. An intercom on a channel can only hear an intercom on the same channel or on the paging channel. Battery: The AA Alkaline batteries (not provided) will last up to a year depending on use. When batteries are low intercom will emit three beeps every ten minutes. A DC Adapter (not provided) can also be used to power the intercom. In this case, the channel lights will remain on. Conference Mode: Conference Mode allows multiple intercoms to participate in a conversation compared to Normal Mode in which only two intercoms can communicate. All intercoms must be set to the same channel or the paging channel to be in Conference Mode. To put intercom in Conference Mode set Dipswitch #2 to UP position. Monitor Mode: Monitor Mode is used to monitor the noise in a specifi c room. Place the intercom in the room that is to be monitored and press the Monitor button until a tone is heard. For extended Monitor usage, consider using a plug-in transformer. Any other networked intercom can listen to that room. If a specifi c channel is selected for Monitor Mode then only other intercoms on that channel or on the paging channel can listen. Press the Talk button to exit Monitor Mode. A tone will be heard indicating Monitor Mode is no longer active. Voice Activation Mode (VOX): Voice Activation Mode (VOX) allows a call to be answered without pressing the Talk button. Once a call is heard on an intercom which has been set to VOX, a response can be given by speaking loudly into the intercom. There will be a slight delay when VOX is fi rst activated by a voice, but will continue to transmit audio until the speaking stops. To put intercom into VOX, place Dipswitch #1 to the UP position. While in VOX mode, a call may be initiated by pressing the TALK button. Volume UP Button Talk Button Learn Button Dipswitch #1 AC Adapter Dipswitch #2 Models NLS1, NLS2, NLS1C & NLS2C Wireless Portable Intercom - Extreme Range ® VOLUME MONITOR CHANNEL HOLD OFF ACTIVE TALK 13 2 4 MONITOR HOLD OFF 1 3 2 4 VOLUME TALK ACTIVE OPTIONAL 1 2 1 2 Channel Select Button Channel Lights Active Light Volume DOWN Button Monitor Button Speaker VOLUME MONITOR CHANNEL HOLD OFF ACTIVE TALK 13 2 4 VOLUME MONITOR CHANNEL HOLD OFF ACTIVE TALK 13 2 4 2 Assemble Intercom Step 1 Install 4 AA Alkaline batteries (not provided). Step 2 Adhere rubber pads to bottom. Repeat Steps 1 and 2 for any additional intercoms. Programming Intercom The intercom must be programmed to at least one other intercom to become a netw...

Ce manuel est également adapté pour les modèles :
Téléphones filaires - NLS1C (1.06 mb)
Téléphones filaires - NLS2 (1.06 mb)
Téléphones filaires - NLS2C (1.06 mb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories