Log:
Évaluations - 3, GPA: 3.7 ( )

Instructions La Crosse Technology, Modèle 512-807

Fabricant : La Crosse Technology
Taille : 95 kb
Nom Fichier :
Langue d'enseignement: en
Aller à la télécharger



Par ce dispositif a également d'autres instructions :

Facilité d'utilisation


Note: The following steps often refer to two buttons: “+ ” and “ - / °F/ °C”. The “+ ” button is used to increase setting values and the “ -/ ° F/° C” button is used to decrease setting values. To enter setup mode and begin the configuration process, press and hold the “ SET” button for about 3 seconds, or until the clock beeps. The display is now flashing “ 12 Hr” and you are ready to begin configuring your clock. 1. Set 12 or 24 Hour Time Mode With the display flashing “ 12 Hr”, press the “ + ” or “ - / °F/ ° C” button to select either a 12 or 24 hour time mode. 2. Set Time - Hour Once you have chosen 12 or 24 hr time mode, press the “ SET” button again and the Hour digits will begin to flash. Use the “+ ” and “ - / °F/°C” buttons to select the correct hour. 3. Set Time - Minute Once the hour is set, press the “ SET” button again and the Minutes digits will flash. Use the “+ ” and “ - / °F/ ° C” buttons to select the correct minute. 4. Set Date – Year Once the minute is set, press the “ SET” button again and the Year digits will flash. Use the “ + ” and “ - / °F/ ° C” buttons to select the correct year. Page 3 of 8 5. Set Date - Month Once the year is set, press the “ SET” button again and the Month digits will flash. Use the “ + ” and “ - / F°/ C°” buttons to select the correct month. 6. Set Date - Date Once the month is set, press the “ SET” button again and the Date digits will flash. Use the “ + ” and “ - / °F/ C°” buttons to select the correct date. To Change the Temperature Units To change the temperature reading between Fahrenheit or Celsius, press the “ - / °F/°C” button. To Set the Time Alarm 1. To turn the alarm on: Press the " ALM" button. The LCD will display the alarm icon . 2. To set the Alarm Time - Hour: Press and hold down the " ALM" button for 3 seconds until the hours digits flash. Use the “+ ” button to set the hour. Press the " ALM" button to confirm your setting and move to setting the minutes. 3. To set the Alarm Time - Minutes: The Minutes digits of the Alarm Time will flash. Use the “+ ” button to set the minutes. You can hold the " + " button in to speed up the setting of minutes by using five minute increments. Press the " ALM" button to confirm your minutes setting and to end the setting procedure. 4. To activate or deactivate the daily alarm: Briefly press the “ ALM” button once. When the alarm is active the clock displays the alarm icon in the upper right corner. When the alarm is deactivated, the alarm icon will not display. 5. About the Time Alarm: After 15 seconds without pressing any button, the clock switches automatically from alarm setting mode to normal clock mode. To Use The Alarm The alarm can be silenced by pressing any button. If it is not silenced, it will sound for 2 minutes before stopping on its own. The alarm repeats automatically after 24 hours. Page 4 of8 If the “ SNZ” button is pressed, the alarm will silence for approximately 5 minutes, after which it will begin to sound again. The alarm uses 3...

Ce manuel est également adapté pour les modèles :
Télécommande - DIGITAL CLOCK WITH INDOOR TEMPERATURE WT-8002U (95 kb)
Télécommande - Radio Controlled Projection Alarm WT-5110 (95 kb)
Télécommande - Radio Controlled Projection Alarm WT-5350 (95 kb)
Télécommande - TIMER WALL WT-8100 (95 kb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories