Log:
Évaluations - 5, GPA: 3.2 ( )

Instructions La Crosse Technology, Modèle WS- 1912

Fabricant : La Crosse Technology
Taille : 95 kb
Nom Fichier :
Langue d'enseignement: en
Aller à la télécharger



Par ce dispositif a également d'autres instructions :

Facilité d'utilisation


......... .......... .......... ....... 4 To Use The Alarm ........ .......... .......... .......... ....... 4 Battery Replacement Information ..... .......... ....... 5 Mounting the Unit ......... .......... .......... .......... ....... 5 Online Resources......... .......... .......... .......... ....... 5 Care and Maintenance . .......... .......... .......... ....... 5 Troubleshooting ... ......... .......... .......... .......... ....... 6 Warranty Information .... .......... .......... .......... ....... 6 Page 1 of 8 Button View Page 2 of8 Install Battery Install Battery Insert 1 new "AA", 1.5 volt ALKALINE batteries into the clock according to the polarity marked on the battery compartment. Once the battery is properly installed in the clock, the unit will beep and all segments of its LCD will briefly light up. The indoor temp and the time (displayed as 12: 00) will appear on the LCD. If the time and temp do not appear after 30 seconds, please reinstall the battery and try again. Once the indoor temp is displayed, proceed to the next step. Set the Time and Date Please read through all of the steps below before starting to configure your clock. Once you have started the configuration, you will be able to move from one step to another by pressing the “ SET” button. If at any point during the setup process you need to start over, avoid pressing any buttons for roughly 30 seconds or wait until the display stops flashing, then repeat the steps outlined in this section. Note: The following steps often refer to two buttons: “+ ” and “ - / °F/ °C”. The “+ ” button is used to increase setting values and the “ -/ ° F/° C” button is used to decrease setting values. To enter setup mode and begin the configuration process, press and hold the “ SET” button for about 3 seconds, or until the clock beeps. The display is now flashing “ 12 Hr” and you are ready to begin configuring your clock. 1. Set 12 or 24 Hour Time Mode With the display flashing “ 12 Hr”, press the “ + ” or “ - / °F/ ° C” button to select either a 12 or 24 hour time mode. 2. Set Time - Hour Once you have chosen 12 or 24 hr time mode, press the “ SET” button again and the Hour digits will begin to flash. Use the “+ ” and “ - / °F/°C” buttons to select the correct hour. 3. Set Time - Minute Once the hour is set, press the “ SET” button again and the Minutes digits will flash. Use the “+ ” and “ - / °F/ ° C” buttons to select the correct minute. 4. Set Date – Year Once the minute is set, press the “ SET” button again and the Year digits will flash. Use the “ + ” and “ - / °F/ ° C” buttons to select the correct year. Page 3 of 8 5. Set Date - Month Once the year is set, press the “ SET” button again and the Month digits will flash. Use the “ + ” and “ - / F°/ C°” buttons to select the correct month. 6. Set Date - Date Once the month is set, press the “ SET” button again and the Date digits will flash. Use the “ + ” and “ - / °F/ C°” buttons to select the correct date. To Change the Temperat...

Ce manuel est également adapté pour les modèles :
Télécommande - DIGITAL CLOCK WITH INDOOR TEMPERATURE WT-8002U (95 kb)
Télécommande - Radio Controlled Projection Alarm WT-5110 (95 kb)
Télécommande - Radio Controlled Projection Alarm WT-5350 (95 kb)
Télécommande - TIMER WALL WT-8100 (95 kb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories