Évaluations - , GPA:
(
)
)
Fabricant : Bissell
Taille : 377.46 kb
Nom Fichier : 5d29c7fa-efc2-4bfb-9acd-926c8b0dd0a4.pdf
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Facilité d'utilisation
These products may react with theplastic materials used inyour QuickSteamer,® causing cracking or pitting. Tip: Always vacuum thoroughly before you deep clean. If possible, move larger furniture to an area you will not be cleaning. 2. Formula Measuring Cap Unscrew to Remove 6. Power Switch 7Pre-treat stubborn stains and highly soiled carpet in hallways and other high-traffic areas. Spray soiled area with BISSELL® Tough Stain PreCleaner.™ Use a stiff-bristled brush to work formula into carpet pile. Wait 3 -5 minutes before deep cleaning. Turn Power Switch [located on the side of the Lower Body] to ( ) ON. With foot, press the Detent Lever on right side of Lower Body. Depress Spray Trigger to spray cleaning solution. Do not overwet. To suction up water, repeat motion over same area without depressing Trigger. Repeat Steps 3 and 4 until no more dirt can be removed. Continue to clean entire carpet, working in 3’ x 4’ sections. Empty the Dirty Water Tank when dirty water reaches the full line, or when the Clean Water Tank is empty. See page 9 for instructions. If Floor Nozzle stops spraying, turn Power Switch to OFF ( ) and check water and cleaning solution levels. Refill if needed. Deep Cleaning Pre-Treating Tip: Deep cleaning spots, spills and high traffic areas on a regular basis can prolong carpet life. Tip: It is recommended that every time your Clean Water Tank is emptied of solution that you empty the contents of the Dirty Water Tank. If the Dirty Water Tank gets too full, you may begin to see foam spitting out of the vent cover. When this happens you will know it is time to empty the Dirty Water Tank. Dirty Water Tank 7. Vent Cover 1. 2. 3. 1. 2. 3. 4. 5. 6. 7. 8. 8 *QuickSteamer PowerBrush models only Turn the machine off and unplug from wall outlet. Remove clean and dirty water tanks. Lie machine down to access the bottom of the machine. Unscrew the brush cover. Remove the brush end cap and remove belt from brush. Brush can now be removed. Belt can be removed by sliding off the motor pulley. Clean or replace belt. Attach belt to motor pulley and brush, insert brush into right side end cap. Reattach the left end cap. Slide brush with the end cap attached back into place. Replace the brush cover and screw into place. Belt and Brush Removal - 2070 Series only 10. 11. 10. 11. 3. 4. 5. 5A. 6. 7. 8. 9. 1. 2. 3. 4. 5. 6. 7. 9. 8. printer spreads 3/7/03 4:07 PM Page 9 9 Turn Power Switch to OFF ( ) position. Unplug Power Cord from outlet. Remove and empty Dirty Water Tank. a. Press detent Pedal and tip Handle back, laying it gently on floor. b. Release Dirty Water Tank latches [1 each side] by pulling up from bottom of latch and then out. c. Carefully lift Dirty Water Tank from Lower Body. d. Carry Dirty Water Tank to a toilet or sink. To empty, pour out contents using opening at back of Tank. e. Fill Dirty Water Tank with clean water through the Vent Cover and rinse thoroughly. Discard water. f. Remove lint and hair from Red Gasket in base of unit. (Do not remove gasket) Replace Dirty Water Tank on Lower Body and secure with latches. Wrap Power Cord around Quick Release Cord Wrap™ on side of QUICKSTEAMER® . Wipe all surfaces with a soft cloth. Store cleaner upright in a protected, dry area. NOTE: You may have cleaning solution remaining in the Clean Water Tank. You may store your QuickSteamer this way for the next cleaning task, but never keep soiled solution in the Dirty Water Tank. a. c. d. Vent Cover e. b. When you’re done CAUTION: Do not store unit where freezing may occur. Damage to internalcomponents may result. Routine Maintenance WARNING: To reduce the risk of injury from moving partsand/or electrical shock, turn Power Switch OFF and disconnect polarizedplug from electricaloutlet before performingtroubleshooting checks. 1. 2. 3. 4. 5. 6. a. c. d. Vent Cover e. b. When you’re done CAUTION: Do not store unit where freezing may occur. Damage to internalcomponents may result. Routine Maintenance WARNING: To reduce the risk of injury from moving partsand/or electrical shock, turn Power Switch OFF and disconnect polarizedplug from electricaloutlet before performingtroubleshooting checks. 1. 2. 3. 4. 5. 6. Remedies Refill Tank with water and formula Remedies Check Tank for proper alignment and secure with side latches Empty Tank 10Reduced spray or no spray. Possible Causes Clean Water Tank empty Deep Cleaner not picking up cleaning solution. Possible Causes Dirty Water Tank not aligned/secured Dirty Water Tank is full Trouble Shooting For information about repairs or replacement parts, or questions about your warranty, call: BISSELL Consumer Services 1-800-237-7691 Monday - Friday 8 a.m. — 10 p.m. ET Saturday 9 a.m. — 8 p.m. ET Or write: BISSELL Homecare, Inc PO Box 3606 Grand Rapids, MI 49501 ATTN: Consumer Services Or visit the BISSELL website -When contacting BISSELL, have model number of unit available. Please record your Model Number: ___________________ Please record your Purchase Date:...