Évaluations - 3, GPA: 4.7
(
)
)
|
Facilité d'utilisation
Signal search. Setting Up English Unpacking The package should include the following items: - 2 handsets with belt clips - 8 alkaline batteries - This manual - Guarantee Card Please Note! An optional Accessory Pack is available (pmr a-pack) that contains: - 2 Ni-MH rechargeable battery packs, - A twin handset charger and mains adapter, - 2 headsets, - 2 carry cases. Approved usage This product can be freely used in Australia and New Zealand without a license. The handsets are made from durable plastic for indoor and outdoor use, however, they are not resistant to rain, fluid ingress, abuse or any careless treatment. Batteries Each unit requires four AAA 1.5 V alkaline batteries to function (included). The battery symbol in the display indicates when it is time to change the batteries. The battery symbol has two segments, which disappear as the battery charge decreases. When the batteries are almost fully discharged the battery symbol flashes and a warning tone is emitted, the batteries should be changed as soon as possible. Good quality alkaline batteries will allow approximately 4 hours talk time or 100 hours of stand-by time. 1. Remove the belt clip if fitted (see below). 2. Remove the battery cover by pressing on the indentation markings, and pushing out (away from aerial). 3. Insert the batteries ensuring correct polarity is observed. 4. Replace the battery cover. 3 English Setting Up Belt clips A belt clip is included, which can be fitted on the back of the handset once the batteries have been installed. The belt clip allows the handset to be attached to a belt, waistband or similar. To remove, lift the small tab at the top of the clip and simultaneously push upwards. Range The communication range is dependent on many factors, with the maximum range being achieved when there are no obstacles in the transmission path (line of sight). Under optimum conditions the maximum range can be up to 5km. There will be a reduction in the range when the units are used in built up areas, undulating terrains and vehicles. Headset The handset can be used with the headset supplied in the optional Accessory Pack (pmr a-pack) which can be purchased from your local DORO retailer. When the headset is connected, the microphone and speaker on the handset are automatically disconnected, all other functions remain unchanged. Please note! Use only DORO original headsets with these PMR units. Adjust the Call signal and headset volume immediately upon connecting a headset, as these settings may initially be too loud. Turning the handset On/Off To turn the handset On or Off press and hold the ! button (1-2 seconds) until a tune is heard. 4 English Operation Channel Selection This product can operate on the available 40 channels for UHF CB use in Australia and New Zealand, refer to the channel/frequency allocation table on page 7 If the selected channel is being used by other persons an alternate channel can be selected, the channel number will be displayed in the stand-by mode. 1. Press the = button until CHAN flashes in the display. 2. Scroll to the desired channel using the V/V buttons. 3. Press the PTT (Push to Talk) button to save the settings. Please note! Speech telephony is not permitted on channels 22 and 23 and if selected an error tone will be heard when the PTT button is pressed. No communication will occur on these channels. Repeater Operation In addition to the standard operating channels 1 to 40 there are an additional 8 settings that can be selected. When selected, by following the procedure above, the display will show the channel number, 1 to 8 plus du indicating the handset is in the repeater mode. This mode allows the handset to operate via a local repeater thereby increasing the communication range. It does this by linking channels 1 - 8 to channels 31 - 38 respectively. When the handset is set to channel 1du it will transmit on channel 31 and receive on channel 1. For more information on the CB repeater network contact the local ACA office in your capitol city, or the local MED office in New Zealand. Channel lock The controls can be locked can be locked to prevent accidental operation of the buttons. Only the PTT and V/V buttons function with the handset locked. 1. Press and hold the N button until the display shows the lock symbol and a beep tone is heard. 2. Unlock by pressing and holding the N button, a beep will be heard and the lock symbol will disappear from the display. 5 English Operation Communication between the handsets 1. Ensure that you use the same channel, e.g. 1. 2. Hold the handset approximately 10 cm in front of you at face height. 3. Press and hold the PTT button, wait a second and then speak clearly towards the handset. Release the button when you have finished speaking. 4. The handset is now ready to receive. 5. If nobody answers, try sending a CALL signal by pressing and holding the...