Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
1. Fluid flow 2. Distance of the spray gun from your work. (4"–8" is average. Closer if necessary.) 3. Pattern Direction (vertical fan, horizontal fan and round) 4. Speed of application 5. Fan pattern control (adjust air cap ring) NOTE: Items 1, 2, and 4 directly relate to each other. RUNNING MULTIPLE SPRAY GUNS WITH A TURBINE It is possible to run the 4-stage turbine system with two spray guns at the same time by installing “Y” Connector to the turbine outlet port. IMPORTANT: If the “Y” connector is installed and only one spray gun operated, the 2nd outlet must be capped or closed so that performance to the single spray gun will not be affected. 7 Operating Instructions and Parts Manual HV2100, HV2105 HVLP Paint Sprayers Operation (Cont.) USING PRESSURE POTS WITH TURBINE SYSTEMS (HV2105) When using a remote cup or pressure pot, it is necessary to introduce compressed air in order to pressurize the remote pot and move the fluid from the pot to the tip/nozzle of the spray gun. In general, 5 pounds of pressure is sufficient for most average viscosity fluids in order to deliver the proper flow of fluid to the tip. Higher pressure would only be necessary for a heavier viscosity fluid. A good test to determine the correct fluid delivery is as follows: 1. Pressurize the pot. DO NOT turn on the turbine. 2. Pull spray gun trigger until a stream of fluid flows from the tip/nozzle. 3. Adjust the pressure until the fluid drops off or bends at approximately 2-1/2 inches (6.35 cm). Pot pressure should be correct at this point. ! WARNING Always depressurize the remote pot using the safety valve when the equipment will be idle for a while. This will prevent excess fluid from remaining in the fluid hose, and prevent a possible accident should the trigger be pulled and paint streams from the spray gun. Always ensure that the remote cup is tightly sealed, and all gaskets are in good shape, to prevent air and fluid leaks. Be sure to flush and clean fluid hose at the end of a work session. For smaller jobs, insert a one gallon can inside the 2.5 gallon pressure pot. This will keep the inside of the pot clean. USING OPTIONAL ACCESSORIES WITH SPRAY GUN OPTION 1: In parts diagram on page 14, locate Item No. 13. Most turbine spray guns are fitted with this blanking cap. You can remove the cap and install Item Nos. 14A and 14B. This gives you the option to attach your air hose onto this port instead of into the handle. To install, unscrew blanking cap. Screw in Item No. 14A and 14B. To use this port, unscrew the male hose coupler and screw onto Item No. 14A. Take the small blanking cap (Item No. 14B) and screw it onto the threads at the bottom of the handle. Reverse these two fittings to use the air hose coupled to the handle. OPTION 2: This will allow you to control the air flow and create textured or splatter paint effects. To install, remove blanking plug (Item No. 13) or Item Nos. 14A and 14B. Screw Item No. 13A into the spray gun. After installing the air control/texturing device, turn the adjusting screw as far as you can counter clockwise (open). Always use in the full open position unless it is necessary to reduce the flow of air, or to create a textured or splatter effect. Additional Instructions for Model HV2105 UNPACKING Remove contents of shipping box and lay out all of the pieces. You will find the cart base, handle, 2.643 gallon (10L) pressure pot (with regulator, gauge, safety valve and connectors attached), 3/8” black lined fluid hose, bag of nuts and bolts for assembly, and instructions. NOTE: Do not place pressure pot onto the cart or insert handle into cart base until the turbine unit is firmly bolted and secured to the cart. Using the cart without the turbine installed can result in the cart tipping over. ATTACHING TURBINE UNIT TO CART 1. Set the turbine unit on the cart base plate with the turbine air hose quick disconnect coupler facing out. 2. Line up the four holes on the turbine base plate with the four holes on the cart base plate. 3. Secure turbine unit to cart base plate with the four hex bolts, washers and hex nuts (supplied). Insert bolt through the holes, place washer over the bolt on the underside, screw hex nut onto bolt and tighten. Be sure that hex nut is tight enough so as not to vibrate loose. 4. Insert the chrome handle into the frame tube. Be sure to push handle all the way down so that the spring loaded buttons lock into place, securing the handle firmly. 5. Plug turbine unit into outlet on side of the Cart. 4. Place the 2.643 gallon (10L) pressure pot onto the pressure pot deck. Align the fluid outlet toward the front of the cart. This will position air inlet toward the back of the cart. NOTE: Pressure pot support rings can be adjusted for use with different size pressure pots. CONVERT SPRAY GUN FROM CUP GUN TO PRODUCTION FLUID FEED 1. Remove cup assembly. a. Disconnect the upper section of the air feed tube from the nonchpower.com 8 Operating Instructions and Parts Manu...
Ce manuel est également adapté pour les modèles :Guns - HV2100 (2.62 mb)