Évaluations - , GPA: ( )

Instructions Transition Networks, Modèle SSDTF1014-100

Fabricant : Transition Networks
Taille : 101.43 kb
Nom Fichier : 33202_SSDTF10xx-100.pdf

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

TN PN Requirement Location 25034 or 3525 240 volts, 50 hertz United Kingdom 25034 or 3525 230 volts, 50 hertz Europe 3518 120 volts, 60 hertz USA/Canada/Mexico 3514 100 volts, 50-60 hertz Japan 25034 or 3525 240 volts, 50 hertz Australia Environment Typical Operating Temperature* : 0° to 50° C (32° to 122°F ) Storage Temperature: -20° to 85° C (-4° to 185°F) Humidity 10-90%, non condensing Altitude 0-10,000 feet Warranty Lifetime DECLARATION OF CONFORMITY Name of Mfg: Transition Networks 6475 City West Parkway, Minneapolis MN 55344 USA Model: SSDTF10xx Series Copper-to-Fiber Media Converter Part Number: SSDTF1011-100, SSDTF1012-100, SSDTF1013-100, SSDTF1022-100 Regulation: EMC Directive 89/336/EEC Purpose: To declare that the SSDTF10xx to which this declaration refers is in conformity with the following standards. EN 55022:1994; EN 55024:1998; FCC I, the undersigned, hereby declare above Directive(s) and Standard(_January 8, 2001_____ Stephen Anderson, Vice-Date CABLE SPECIFICATIONS (continued) Twisted-Pair Copper Cable Twisted pair connection requires two active pairs. The two active pairs in a T1/E1 network are pins 1 & 2 and pins 4 & 5. Use only dedicated wire pairs (such as blue/white & white/blue, orange/white & white/orange) for the active pins. Category 3 or better twisted-pair copper wire is required. Either shielded twisted-pair (STP) or unshielded twisted-pair (UTP) can be used. T1: Gauge 24 to 22 AWG Attenuation 2.6 dB/100 meters @ 1.0 MHz Differential Characteristic Impedance 100 . ±10% E1: Gauge 24 to 22 AWG Attenuation 2.6 dB/100 meters @ 1.0 MHz Differential Characteristic Impedance 120 . ±10% Dry-Contact Relay RJ-45 dry-contact relay opens if power, signal detect/copper or signal detect/fiber are lost. Operational rating on pins 3 and 6: 0-30VDC maximum 1A Relay 3 RJ-45 6 Switch-Selectable Configurations T1 COPPER RJ-45 Configured as either "long haul" or “ short haul” on 100 ohm cable, with a variety of selectable distance settings. E1 COPPER RJ-45 Configured as either "long haul" or “ short haul” on 120 ohm cable. STRAIGHT-THROUGH/CROSSOVER RJ-45 Allows straight-through cable to be used where crossover-configuration cable is required. Switch-Selectable Functions LOOPBACK TEST FUNCTION A loopback switch facilitates installation and network debug The path for the SSDTF10xx loopback is shown: FiberTP TP TRANSMIT ALL ONES FUNCTION A selectable Transmit All twisted-pair interface allows “ all ones” pattern on that interface when signal detect is lost, which creates the equipment connected INSTALLATION CABLE SPECIFICATIONS CAUTION: Wear a grounding device and observe electrostatic discharge precautions when setting switch and when installing Media Converter Slide-in- Fiber Cable Module in the Media Conversion Center. Failure to observe this caution could Bit error rate: . 10-9 result in damage to, and subsequent failure of, the Media Converter Slide-in- MULTIMODE Module. Fiber Optic Cable Recommended: 62.5 / 125 .m multimode fiber Set...