Use these to connect the power cords from your components to this unit. The power to the SWITCHED outlets is controlled by this unit’s STANDBY/ON switch or the provided remote control transmitter’s STANDBY/ON key. These outlets will supply power to any component whenever this unit is turned on. The maximum power (total power consumption of components) that can be connected to the SWITCHED AC OUTLETS is 100 watts. CONNECTING SPEAKERS Connect the SPEAKERS terminals to your speakers with wire of the proper gauge (cut as short as possible). If the connections are faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is the + and – markings are observed. If these wires are reversed, the sound will be unnatural and lack bass. Caution Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or speakers. How to Connect: Banana Plug connections are also possible. Simply insert the Red: positive (+) Banana Plug connector into the corresponding terminal. Black: negative (–) 123 A Unscrew the knob. . Insert the bare wire. [Remove approx. 5mm (1/4”) insulation from the speaker wires.] . Tighten the knob and secure the wire. Use speakers with the specified impedance shown on the rear of this unit. Note One or two speaker systems can be connected to this unit. If you use only one speaker system, connect it to either the SPEAKERS A or B terminals. IMPEDANCE SELECTOR switch Be sure to switch the position only when the power to this unit is not on. Select the position whose requirements your speaker system meets. WARNING Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise this unit may be damaged. IF THIS UNIT FAILS TO TURN ON WHEN THE STANDBY/ON SWITCH IS PRESSED; The IMPEDANCE SELECTOR switch may not be set to either end. If so, set the switch to either end when this unit is in the standby mode. IMPEDANCE SELECTOR (U.S.A. model) A OR B:4WMIN. /SPEAKER A B:8WMIN. /SPEAKER A OR B:6WMIN. /SPEAKER A B:I2WMIN. /SPEAKER IMPEDANCE SELECTOR SET BEFORE POWER ON A (Left position) If you use one pair of speakers, the impedance of each speaker must be 4W or higher. If you use two pairs of speakers, the impedance of each speaker must be 8W or higher. (Right position) If you use one pair of speakers, the impedance of each speaker must be 6W or higher. If you use two pairs of speakers, the impedance of each speaker must be 12W or higher. The impedance of each speaker must be 6. or higher. If you use one pair of speakers, the impedance of each speaker must be 8. or higher. If you use two pairs of speakers, the impedance of each speaker must be 16. or higher. For Custom Installer For U.S.A., Canada and Australia models only REMOTE CONTROL (IN, OUT) terminals These terminals are used for custom installation system. When this unit is connected to the components for custom installation system, you can operate this unit with the system remote control. Connect the REMOTE CONTROL IN terminal of this unit to the output terminal of the central controller for custom installation system. By connecting the REMOTE CONTROL OUT terminal of this unit to the REMOTE CONTROL IN terminal of the other component, you can also operate the component with the system remote control. In this way, up to 6 components can be connected in series. GND REMOTE CONTROL PLAY REC PHONO CD IN OUT TAPE 1 /MD PLAY REC TAPE 2 1 3 4 3 5 AUX AUDIO SIGNAL or 4 6or English ANTENNA CONNECTIONS . Each antenna should be connected to the designated terminal(s) correctly, referring to the following diagram. . Both AM and FM indoor antennas are supplied to this unit. In general, these antennas will provide sufficient signal strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may result in improvement. FM ANT AM ANT GND 75W UNBAL. Outdoor FM antenna Outdoor AM antenna AM loop antenna (included) 75-ohm/300-ohm antenna adapter 75-ohm/300-ohm antenna adapter 75-ohm coaxial cable 300-ohm feeder Indoor FM antenna (included) Ground Connecting the AM loop antenna 1 2 3 * The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall. * The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit. A A A Orient so that the best reception is obtained. GND terminal For maximum safety and minimum interference, connect the GND terminal to a good earth ground, which is a metal stake driven into moist earth. Notes . When connecting the indoor FM antenna, insert its connector into the FM ANT terminal firmly. . If you need an outdoor FM antenna to improve FM reception quality, either 300-ohm feeder or coaxial cable may be ...
)
