This system provides a lower cost and a higher performance alternative to the concept of feeding home runs (a run of cable) to a single large distribution amplifier. In the Serial Distribution System, up to thirty DA1904SX units may be installed at each monitor location along the bus, which is created by using VGA-type cables connected to the 15-pin HD input and loop output. Each monitor is fed from the RGBHV output. In this system, the DA1904SX units may receive their origin feed from an output

This switch should normally be set in the 4V position. Some older display equipment may require a sync level of 2V in which case this switch may be used, but this would be rare. 4.4 POWER The DA1912SX requires the use of a 9V 500mA power supply, which is included with the unit. A variety of different power supplies are available for international use. 4.5 MOUNTING THE DA1912SX To mount the DA1912SX, Altinex offers "L" shape mini-brackets, the DA1295SX, which provides wings on either side of the

The input termination is switch selectable to either be 600 Ohms or high impedance. The DAV0106-V1A2 Distribution Amplifier will allow the connection of video and audio amplifiers simultaneously. The DAV0106-V1A2 Distribution Amplifier is a state-of-the-art product with a bandwidth of 130MHz for video signals, which enables it to remain transparent to the incoming video signals passing through it. It also has a bandwidth of 10Hz to 20kHz for audio signals. The DAV0106-V1A2 can pass NTSC, PAL or

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. • Any changes or modifications to the unit not expressly approved by Altinex, Inc. could void the user’s authority to operate the equipment. ABOUT YOUR DISTRIBUTION AMPLIFIER 2 The DAA0106-V0A2 is a product of exceptional quality and design, which includes stereo audio amplifiers. The audio amplifier is designed to provi

DA1902SX Mechanical ELECTRICAL DA1902SX Input Video Signal Analog Signal 1.5V p-p max Impedance 75 Ohms Input Sync Signals Horizontal, Vertical, & C-Sync TTL(+/-) Sync on Green -0.3V Impedance 10 k Ohms Output Video Signals Analog Signal Gain of 1.05 (+/-5%) Fall/Rise Time (ns) 1.4 Impedance 75 Ohms Output Sync Signals Composite Sync TTL(+/-) Sync on Green -0.3V Impedance 22 Ohms Frequency Compatibility Typical Video Bandwidth 380 MHz Minimum Video Bandwidth 350 MHz Horizontal 15-200 kHz 3 DISTR

Keep this manual handy for future reference. These safety instructions are to ensure the long life of your DA1931CT and to prevent fire and shock hazard. Please read them carefully and heed all warnings. 1.1 GENERAL • Qualified ALTINEX service personnel, or their authorized representatives must perform all service. 1.2 INSTALLATION • To prevent fire or shock, do not expose this unit to rain or moisture. Do not place the DA1931CT in direct sunlight, near heaters or heat radiating appliances, or n

Output offers standard RGBHV or RGBS format. MECHANICAL TR6102HD Width (inches) 8.50in (216mm) Height (inches) 1.75in (44mm) Depth (inches) 4.93in (125mm) Weight (pounds) 2.0lbs (0.91kg) Ship Weight (pounds) 4.0lbs (1.82kg) Material 0.1” Al Finish Gray Front/Back Panels Lexan Overlay T° Operating 10°C-35°C T° Maximum 50°C Humidity 90% non-condensing MTBF (calculations) 40,000hrs Table 2. TR6102HD Mechanical ELECTRICAL TR6102HD Input Video Signal (Y) Nominal Level 0V to 0.7Vp-p (Y) Maximum Level

If the source offers a VGA-type 15-pin HD connector, then use a special cable - Altinex part # MS8102CA (15-pin HD Male to 5 BNC Male 6 feet cable) may be used. NOTE: You may have to use an interface (DA1910SX or VA6855WM) with your source computer to provide the appropriate signal format type and to allow the use of a local monitor. Do not use a Y-cable or monitor breakout cable to connect the computer to the DA1222AT because this will affect the quality of the high-resolution input signal. Ste

The DA1226AT offers excellent bandwidth performance (minimum 350 MHz) and a typical bandwidth of nearly 450 MHz, allowing it to remain virtually transparent to high resolution signals. Though primarily designed to pass an RGBHV signal format, the DA1226AT can also pass RGBS, RGsB, Component Video (Y, R-Y, B-Y), S-Video (Y/C), and Composite Video by using the appropriate channels. The DA1226AT outputs the same sync level as it receives on its input. The DA1226AT offers a low-profile design, which

The AC/DC switch is used to select AC or DC coupling of video signal through a distribution amplifier. The TERM switch is used to terminate or unterminate RED, GREEN, & BLUE inputs with 75 Ohms. The GAIN switch is used to set gain to 1 or 1.3. The EQLZ switch is used to compensate for longer cable runs. APPLICATION DIAGRAM 5 4.3 SYNC CONTROL SWITCHES The DA1322AT has separate Sync control switches: TERM H, C SYNC, TERM V, and SYNC G. The TERM H switch is used to terminate or unterminate horizont