NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.” Owner’s record For your convenience, record the model number and serial number (you will find them on the rear of your unit) in the space provided below. Please refer to them when you contact your Aiwa dealer in case of difficulty. Model No. Serial No. (Lot No.) AV-D25 Read the Operating Instructions carefully and completely before operating the unit. Be sure to keep the Operating Instructions for future reference

When a station is stored, a preset number is assigned to the station. Use the preset number to tune in to a preset station directly. 1 Turn the FUNCTION selector to select theTUNER function, and press the VIDEO 1/5.1 CH/BAND button repeatedly to select the desired band. Then press the UP or DOWN button to select a station. 2 Press the ENTER button to store the station. A preset number assigned to the station, beginning from 1 in consecutive order for each band, is displayed for two seconds. 3 Re

Be sure to set the FRONT SPEAKERS A and B buttons to 10FF. Otherwise sound is output from the speakers. The 5.1 CH function, Dolby Pro Logic or DSP system is automatically canceled when the headphones are plugged in. To turn the unit off, press the POWER button. 7 ENGLISH DOWN,UP VOLUME VOL I MUTING I BALANCE T-BASS VOLUME CONTROL Turn the VOLUME control on the unit, or press the VOL buttons on the remote control. The vc)lume level is shown on the display for four seconds. It can be adjusted bet

RADIO RECEPTION (cont.) pg. 11 PRESETTING STATIONS The unit can store a total of 32 preset stations. When a station is stored, a preset number is assigned to the station. Use the preset number to tune in to a preset station directly. 1 Press TUNER to select a band, and press the UP or DOWN button to select a station. Direct tuning is also available. 2 Press the SET button to store the station. A station is assigned a preset number, beginning from 1 in consecutive order for each band. 3 Repeat st

When the front speakers are turned on, “SP3” lights up on the display window. NOTE • When you turn off the front speakers, the surround mode (Dolby Digital, Dolby Pro Logic or DTS) or the DSP mode will be canceled. • When the front speakers are turned off, SURROUND and DSP on the front panel cannot be used. (“CAN’T USE” will be displayed). CONNECTING THE SUPPLIED ANTENNAS 2 22222 Connect the FM antenna to the FM 75. terminal and the AM antenna to the AM LOOP jack. FM antenna ANTENNA AM LOOP FM 7

The unit provides 5 DSP preset modes. 1 Press DSP. 2Within 6 seconds, turn MULTI JOG to select the desired DSP mode. The “DSP” and “S” (surround speakers) indicators light up. DISCO HALL LIVE CHURCH MOVIE When the music source is monaural The DSP system may not work effectively depending on the DSP mode selected. To cancel the selected mode Press DSP to display the DSP mode name, and press the button again within 6 seconds. “DSP OFF” appears on the display. To select with the remote control 1 Pr

Alternatively, press ior kon the remote control. You can tune in the desired preset station directly by pressing the numbered buttons on the remote control. -To select preset number 25, press 2 and 5. -To select preset number 7, press 7. To clear a preset station 1Tune in the station by preset tuning. 2 Press ENTER, and press ENTER again while the frequency flashes on the display. Alternatively, press ENTER or C on the remote control, and press ENTER while the frequency flashes on the display. R

“TAPE ON” appears on the display for four seconds, and then the source name selected in step 1 comes back on. To cancel the tape monitor, press it again so that “TAPE oFF” appears. . Any sound control except the BBE system has no effect on recording (see page 7). Recorded sound cannot be monitored if the connected tape deck is not a three-head system. 9 ENGLISH DIRECT TUNING MONO 1,2 3 DOWN~, UPA TUNER I II 1 Press the TUNER button repeatedly to select the desired band. ~ If the power is turned

There are four modes with matching graphic equalization modes. Equalization modes are selected automatically and can also be selected or turned off to suit your preference. Press one of the DSP buttons (DANCE:, LIVE, HALL or ARENA). The selected mode name appears on the display for two seconds, and the selected DSP and matching GEQ modes on the display are enclosed with parentheses. DANCE ||lliÉpf rIALL Selected mode- '-TiTiT HALL ARENA : ■; ; ; i\ i i ! JJ i 1 1 s«! L. L. Selected D

it can store a total of 30 signal codes of the external remote control. Use the remote control. 1 Press the LEARN button. “ADDRESS flashes on the display window. 2 Press one of the MEMORY buttons (A-O), then the ADDRESS 1 or 2 button to designate the button on which the signal code is stored. The indication you designated appears on the display. Example: When designating the ADDRESS 1 on the MEMORY A button. 3 Pointing the remote control of the connected equipment toward the unit, press the func