Log:
Téléchargements : 20   Taille : 876 kb   Fabricant : ARC Audio  
Catégorie : Récepteur et amplificateur
@name

DUAL INPUT. 5 BAND PARAMETRIC EQ. MICROPROCESSOR CONTROLLED. 12/24 DB HIGH PASS CROSSOVER. 3 STEREO PLUS SUMMED SUB AND CENTER OUTPUTS. 12/24/48 DB SUB CROSSOVER. MANUAL AND USER GUIDE DXE DIGITAL CROSSOVER EQUALIZER DXE Manual Table of Contents Introduction Welcome to the Arc Audio family of performance signal processors. A blend of Arc Audio’s lengthy experience in performance car audio design combined with the legendary engineering skills of Robert Zeff and the staff at Nikola Engineering. Yo

Téléchargements : 2   Taille : 1022 kb   Fabricant : ARC Audio  
Catégorie : Récepteur et amplificateur
@name

Always use the proper size power wiring when installing your new amplifier. Depending on the size of your amplifier a 4 gauge or larger wire should be used for power and ground connections. It is also advised and recommended that a fuse be installed on the power wire within 18 inches of the batter or power source for safety. Setting the Gains So you're worried that your 4 Volt output head unit will be too much for the ARC Audio's 2.5 Volt input stage. Don't Be ARC Audio Amplifiers input stag

Téléchargements : 12   Taille : 1022 kb   Fabricant : ARC Audio  
Catégorie : Récepteur et amplificateur
@name

Please select a dry location in the trunk or passenger compartment only. Do not mount the amplifier to any area that may have excess vibration (like the subwoofer box). Position the amplifier in an area that receives sufficient airflow for proper heat dissipation. 2 Supplying Enough Power The Laws of Nature Your amplifier Does NOT make power. It converts power, or current,from your cars electrical system and turns it into a high power musical energy. If the amp can't get all the power it need

Téléchargements : 1   Taille : 1022 kb   Fabricant : ARC Audio  
Catégorie : Récepteur et amplificateur
@name

Meaning it has more than one channel of speaker outputs. It is equipped with a large block style terminal for speaker connection. Make this connection carefully and neatly. Strip your wire back and twist the exposed leads and insert into the block terminal while being careful that there is no loose or frayed strands of wire and tighten the Phillips head screw down on the terminal till the wire is tightly secured in place. If the wires ever come in contact with each other the amplifier will go in

Téléchargements : 1   Taille : 1022 kb   Fabricant : ARC Audio  
Catégorie : Récepteur et amplificateur
@name

It may take some time to get the system fully adjusted. During this time the amp is drawing current from the battery. You should check the battery voltage from time to time and re-charge it if it gets low. Battery voltage can affect the way the amplifier performs. 14. You're done. Now have fun. 7 FD2100 and FD2200 BRIDGED 4 OHMS Set to Set to LOW L+RSUM ) 0 0 0 0 1000000000000 4 OHMS B FD2100 and FD2200 STEREO FULL RANGE OR HIGH PASS 4 OHMS/2 OHMS Set to Set to HIGH or FULL STEREO O

Téléchargements : 0   Taille : 460 kb   Fabricant : ARC Audio  
Catégorie : Récepteur et amplificateur
@name

0MIN MAX 55 250 GAIN LOW 10 50 SUB SONIC R L BOOST 15 BASS Speaker outputs This amplifier is a multi channel amplifier design. Meaning it has more than one channel of speaker outputs. It is equipped with a large block style terminal for speaker connection. Make this connection carefully and neatly. Strip your wire back and twist the exposed leads and insert them into the block terminal while being careful that there is no loose or frayed strands of wire and tighten the Allen head screw down on t





catégories