Évaluations - 1, GPA: 3
(
)
)
|
Facilité d'utilisation
CHECK FORWARD BELT TENSION Forward belt tension may decrease over time. It must be adjusted within the first half hour of operation, and checked after every two hours of operation. Proper adjustment will assure long belt life.Too much or too little belt tension will cause premature belt failure.To check and adjust the forward belt tension: 1. Turn off engine. Engine must be cool. 2. Remove spark plug wire from spark plug. 3. With drive control levers in neutral position, measure length of spring when compressed. 4. Pull down on drive control levers and remeasure length of spring when stretched out. Ideal length would be 1/4" longer. 1" 1-1/4" CAUTION Check forward belt tension regularly.Too much or too little tension will cause premature belt failure. Page 16 Maintenance and Storage CHANGE FORWARD/REVERSE BELT NOTE: Change reverse belt on Model 616RT only. 1. Turn off engine. Engine must be cool. 2. Remove spark plug wire from spark plug. 3. Remove belt guard. . remove the forward belt from the forward engine pulley: -gently pull the engine recoil rope to rotate the pulley. -with the pulley turning, force the forward belt out of the V-groove. -slide the belt free of the engine pulley. -pull the forward belt down and out of the way. . remove the reverse belt from the reverse engine pulley: -gently pull the engine recoil rope to rotate the pulley. -with the pulley turning, force the reverse belt out of the V-groove. -slide the belt free of engine pulleys and reverse belt guides. - pull belt down and away from transmission pulley. . install new reverse belt: -thread belt up from bottom. -place belt around transmission pulley in groove. -place belt under reverse belt guides. -gently pull engine recoil rope while forcing the belt over the edge of the engine pulley into the V-groove. . install new forward belt: - place forward belt in transmission pulley groove. - gently pull the engine recoil rope to rotate the pulley while forcing the forward belt into the V-groove. 4. Replace belt guard. 5. Attach spark plug wire. Reverse On Model 616RT Only Page 17 Maintenance and Storage CHECK OR FILL ENGINE CRANKCASE 1. Add oil according to chart below. Do not overfill. Use a high quality detergent oil classified "For Service SF-SJ,". Use no special additives with recommended oils. Do not mix oil with gasoline. 2. Always check oil level before starting engine. Refer to engine manual for complete instructions. Adapted from Briggs & Stratton Corporation, Form No. 274263-10/99. Engine is shipped from factory without oil.You must add engine oil before starting engine. Adapted from Briggs & Stratton Corporation, Form No. 274263-10/99. *Air cooled engines run hotter than automotive engines. Use of non-synthetic multi-viscosity oils (5W30, 10W-30, etc.) above 40oF (4oC) will result in high oil consumption and possible engine damage. Check oil level more frequently if using these types of oils. **SAE 30 oil, if used below 40o F (4o C), will result in hard starting and possible engine bore damage due to inadequate lubrication. Page 18 Page 19 CHECK TILLER TRANSMISSION GREASE Check the grease level annually. To check the grease level: 1. Move tiller to level ground. 2. Remove grease level dipstick located on the front transmission cover. Correct 00 grease level is indicated between the high and low levels on the dipstick. 3. Replace grease level dipstick in the filler hole. 4. Note that the front wheel transmission and rear tine transmission are one common reservoir. When you add to the front transmission, you must wait a short period of time for the 00 grease to flow rearward and equalize in both front and rear. The dipstick will read correctly on level ground for both gear units. Grease Fill Hole Tilt Lever Swivel Lever Wheel Lockouts Maintenance and Storage CHECK TIRE PRESSURE Recommended tire pressure is 20 PSI. If tires do not have equal pressure, tiller will pull to one side. LUBRICATION Proper lubrication of moving mechanical parts of your rototiller is a very important part of care and maintenance. You should oil the moving parts shown at 10 hour intervals using a 30 weight oil. TILLER TRANSMISSION IS SHIPPED FROM FACTORY WITH THE PROPER AMOUNT OF 00 LIQUID GREASE. When replacing grease, the tiller transmission holds 18-22 ounces. DO NOT OVERFILL. Maintenance and Storage ENGINE MAINTENANCE Refer to the engine manual included in your parts packet for information on engine maintenance.Your engine manual provides detailed information and a maintenance schedule for performing the following tasks: 1. Check oil level before each use or after every 8 hours of operation. 2. Change oil after first 5-8 hours of operation. Change oil while engine is warm. Refill with new oil of recommended grade. 4. Check spark plug yearly or every 100 hours of operation. 5. Service air cleaner. 6. Keep engine and parts clean. 7. Check engine and equipment often for loose nuts and bolts, keep these items tightened. CLEAN TINE AXLE SHAFT 1. Turn off engi...
Ce manuel est également adapté pour les modèles :Outils de jardin - 1693207 (1.21 mb)
Outils de jardin - 1693704 (1.21 mb)