Évaluations - 4, GPA: 4.3 ( )

Fabricant : Dolmar Taille : 1.32 mb Nom Fichier : Langue d'enseignement:

- Inspect the cutting tool at short regular intervals for damage ( Detect hairline cracks by means of tapping-noise test ). - Operate the Brush Cutter/String Trimmer only with the shoulder strap provided. It should be suitably adjusted before using the Brush Cutter/String Trimmer. Adjust the should strap according to the user’s size to prevent fatigue during operation. Never hold the Brush Cutter/String Trimmer with one hand during use. - During operation always hold the Brush Cutter/String Trimmer with both hands. Always ensure a safe footing. - Operate the Brush Cutter/String Trimmer in such a manner as to avoid inhalation of the exhaust gases. Never run the engine in enclosed rooms ( risk of gas poisoning ). Carbon monoxide is an odorless gas. - Switch off the engine while not in use of the Brush Cutter/String Trimmer, and place it in a safe location to prevent danger to others or damage to the machine. - Never put the hot Brush Cutter/String Trimmer on dry grass or on any combustible materials. - The Brush Cutter/String Trimmer has to be always equipped with an appropriate guard. - All protective installations and guards provided with the Brush Cutter/String Trimmer must be used during operation. - Never run the engine with faulty exhaust muffler. - Stop the engine during transport. - During transport for long distances, the tool-protection must always be used. - Make sure a safe position of the Brush Cutter/String Trimmer during car transportation to avoid fuel leakage. - In transporting the Brush Cutter/String Trimmer, make sure that the fuel tank is completely empty. - When unloading the Brush Cutter/String Trimmer from the truck, never drop the engine on the ground, which may severely damage the fuel tank. - Always lift the entire unit of the machine from the ground when moving the machine. Dragging the fuel tank is highly dangerous and may cause damage of the tank and leakage of fuel, possibly causing fire. 1 2 3 4 5 6 Diagrammatic figure 6 Refueling - Always stop the engine during refueling, keep away from open flames and do not smoke. - Always wear protective gloves during refueling. Change and clean protective clothing at regular intervals. - Be careful not to spill either fuel or oil for environmental protection. Clean the Brush Cutter/String Trimmer immediately if fuel is split. - Avoid any fuel contact with your clothing. Change your clothing immediately if fuel is split on it to prevent clothing catching fire. - Inspect the fuel cap regularly to make sure that it is securely fastened and does not leak. - Always tighten the fuel tank cap securely. Change the location to start the engine (at least 3 meter away from the place of refueling). - Never refuel in closed rooms. Fuel vapors accumulate, which may cause explosions. - Only transport and store fuel in approved containers. Make sure the fuel stored is not accessible to children. Method of operation - Only use the Brush Cutter/String Trimmer in good light and visibility. During the winter season, always be aware of slippery or wet area, ice and snow. Ensure a safe footing. - Never cut above waist height. - Never operate the Brush Cutter/String Trimmer standing on a ladder. - Never use the Brush Cutter/String Trimmer climbing up into trees. - Never work on unstable surfaces. - Remove sand, stones, nails etc. within the working range. Foreign materials may damage the cutting tool and cause dangerous kick-back. - The cutting tool must have reached full working speed before contact with the grass. Kickback - When operating the brush cutter, uncontrollable kickback may occur. - This is particularly the case when attempting to cut within a blade segment between 12 and 2 o’clock. - Never use the brush cutter within a segment between 12 and 2 o’clock. - Never apply the blade of brush cutter to solids, such as bushes and trees, etc., having a diameter in excess of 3 cm or the brush cutter will be deflected at great force with the risk of injuries. Kickback prevention To avoid kickback, ensure the following : - Operation within a blade segment between 12 and 2 o’clock presents positive hazards, especially in using metal cutting tools. - Cutting operations within a blade segment between 11 and 12 o’clock, and between 2 and 5 o’clock, must only be performed by trained and experienced operators, and then only at their own risk. Easy cutting with almost no kickback is possible within a blade segment between 8 and 11 o’clock. Cutting Tools Use only the correct cutting tool. • Re...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :