Évaluations - 1, GPA: 4 ( )

Fabricant : Echo Taille : 1.01 mb Nom Fichier : Langue d'enseignement:

Built in accordance with SAEJ335, this product is approved for use on U.S. Forest Land and within die states of California, Maine, Oregon and Washington if the spark arresting screen is in place and in good repair. 23. SAFETY VIDEO - P/N 99922202540 (Not included with unit and English version only) is available for your review and purchase at a cost of $5.00 from ECHO, INC. or any authorized ECHO dealer. Tlie video overviews safety precautions and proper operating techniques provided in detail in the Safety Manual, and is supplemental to the Safety Manual. Read and understand the Safety Manual for complete information on safe operation. n/MECHO. Specifications SRM-2100SB, SRM-2400SB MODEL SRM-2100SB SRM-2400SB Shaft Length 1500 mm (59 in.) 1500 mm (59 in.) Unit Width 330 mm (13.0 in.) 330 mm (13.0 in.) Unit Height 300 mm (11.8 in.) 360 mm (14.2 in.) Weight (dry) w/Cutter Head (11.9 ib.) 5.4 kg (12.4 ib.) 5.6 kg Engine Type Air cooled, two-stroke, single cylinder gasoline engine Bore 32.2 mm (1.268 in.) 34.0 mm (1.34 in.) Stroke 26.0 mm (1.04 in.) 26.0 mm (1.04 in.) Displacement 21.2 cc(1.29 cu. in.) 23.6cc(1.44cu. in.) Exhaust System Spark Arrestor Muffler Carburetor Zama diaphragm model C1U w/purge Walbro diaphragm model WT w/purge Ignition System Flywheel magneto, capacitor discharge Spark Plug NGK BPM-7A or Champion CJ-7Y Gap 0.65 mm (0.026 in.) Fuel Mixed (Gasoline and Two-stroke Oil) Fuel/Oil Ratio 50:1 ECHO High Performance, two-stroke air cooled engine oil Gasoline 69 Octane unleaded. DO NOT use fuel containing methyl alcohol, more than 10% ethyl alcohol or 15% MTBE, Oil 50:1 ECHO High Performance, two-stroke air cooled engine oil Fuel Tank Capacity 0.4 lit. (13.5 US II. oz.) 0.4 lit. (13.5 US tL oz.) Starter System Automatic Rewind Starter Clutch Centrifugal Type Drive Shaft Upper & Lower 1/4" Flex Shaft 1/4" Flex Shaft Rotating Direction Clockwise viewed from top Cutter Head Nylon line head (2-line) with .095 in. Cross Fire ™ line capacity 13m (40 ft.) Loop Handle* Left - D-Loop, Right - Grip, when operating with line - Standard Shoulder Harness Optional Optional Wide Open Throttle Speed with Trimmer Head 8300 - 8800 RPM 6800-9300 RPM Wide Open Throttle Speed with Blade (Optional) 9500-11,000 RPM 9500-11,000 RPM Idle Speed — 2400 - 3000 RPM 2400 - 3000 RPM ^ * Install and use U-Handle when operating any model with blade. Grass Trimmer/Brush Cutter a q Operator's Manual • J - Assembly POWER HEAD SHAFT/LOWER SHAFT ASSEMBLY Tools Required: None Parts Required: Power Head Shaft, Lower Shaft Assembly, Clamping Knob, Bolt(5x35mm), Flat Washer, Lockwasher 1. Assemble bolt (A) through coupler (B) mounting holes from right to left viewed from open end. 2 Assemble flat washer (C) and lock washer (D) onto bolt end. 3. Assemble and lightly snug clampingknob (E). 4. Set Power Head/Shaft Assembly on a level surface. 5. Pull locator pin (F) and rotate counter clockwise 1 /4 turn to lock out position. 6l Carefully fit lower drive shaft assembly into coupler (B) to decal assembly line (G), making sure that the inner lower drive shaft engages into the upper drive shaft mount. NOTE Lower bearing housing and head assembly must be in line with the engine. 7. Rotate locator pin (F) 1 /4 turn clockwise to engage lower shaft hole (H). Insure locator pin is fully engaged by gently twisting lower drive shaft Locator pin should snap flush in coupler. Full engagement will prevent fimher shaft rotation. & Secure lower shaft assembly to coupler by tightening clamping knob(E), PLASTIC SHIELD INSTALLATION (for Nylon Line Operation) Tools Required: Screwdriver. Paris Required: Plastic Shield, Shield Plate, three (3) 5mm x 15mm screws. urnen/m NOTE The plastic shield is for use with the Nylon Line Head only. Install Metal Shield when using plastic or metal blades. 1. Snap the shield on the bottom of the bearing housing flange. 2 Piaee shield plate on shield, align holes & install three (3) screws. NYLON LINE HEAD INSTALLATION Tools Required: Head Locking Tool Parts Required: Nylon Line Head. 1. Align locking hole in upper plate with notch in edge of gear housing and insert head locking tool (A). 2 Remove rubber retainer from threaded P.T.O. Shaft (C). 3. Be sure upper plate (B) remains on PTO shaft. 4. Thread line head onto shaft by turning it counter clockwise until head is tight against upper plate (B). LOOP HANDLE INSTALLATION Tools Required: Screwdriver. Parts Required: Loop Handle, Handle Support, Four (4) 5mm x 3 Stnra screws with captivated washers, four (4) 5mm nuts. 1. Position loop handle on drive shaft, DO NOT tighten screws yet 2 Position handle for comfortable operation and secure screws. Grass Trimmer/Brush Cutter a c Operator's Manual • O BLADE INSTALLATION Assembly instructions for Blade conversion Kit and U-Handle Kit when operating with optional blades. All Models. IMPORTANT If non-standard monofilament head, METAL/PLASTIC bl...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :