Évaluations - 3, GPA: 4.7
(
)
)
|
Facilité d'utilisation
All external connections must have dielectric grease. 2. Read lead labels before attaching to power source or ground. 3. No other devices may be spliced into wiring harness. 4. Any repairs to wiring harness must be done with heat shrink butt connectors. 5. If inline fuse is installed, use a 35 amp slow blow (Fast-Cast 2000 and Fast-Cast 3000), and use a 60 amp slow blow fuse for Fast-Cast 4000 only. Item No. Part No. Description Qty. 1CS1P39 Male Splice Cord - 18” 1 1CS1P38 Female Splice Cord - 18” 1 1CS1P35 Wiring Harness - 24’ 1 1CS1P36 Dust Cover 1 1CS1P32 Controller 1 1CS4P25 Fast-Cast 4000 Controller 1 1CS4P26 Fast-Cast 4000 Wiring Harness - 25' 1 1CS4P27 Control Power Cable 1 1CS1P52 Diaelectric Grease - 1 1/2 oz. 1 1CS1P40 60'' Ignition Wire 1 August 2001 1165 TRACTOR CAB INC. TRACTOR CAB INC. Operating the Spreader Preparation Caution – Sweep area clear of foreign objects or obstacles that could cause personal injury. Keep other persons, children, or animals out of the area to be spread. Spreader Loading Warning – Do not overload vehicle. Use chart below to calculate weight of material. Weights of material are an average for dry materials. Material Weight Per Cubic Ft. Rock Salt 35-40 lbs. Coarse Sand 85-95 lbs. • Maximum weight of material for the Fast-Cast 175, 180 lbs., the Fast-Cast 2000, 300 lbs., the Fast-Cast 3000, 600 lbs., and the Fast-Cast 4000, 750 lbs. • Be sure to comply with manufacturer’s maximum gross vehicle weight ratings. • Warning – Never leave materials in hopper for long periods of time as salt is hygroscopic and will attract atmospheric moisture and harden up. When spreading sand mix with 20% ice melter to prevent the material from freezing. Spreading Tips • Never exceed 10 m.p.h. when spreading. • For a wider pass, increase spinner speed. • For a heavier pass, drive slower, or increase auger speed (Fast-Cast 4000). • Never operate spreader around pedestrians. • Spread ice melters with the storm to prevent unmanageable levels of ice. • Calculate spread pattern when near vegetation. August 2001 1166 TRACTOR CAB INC. TRACTOR CAB INC. Operating the Spreader (cont.) Spreader Operation Fast-Cast 2000 / Fast-Cast 3000 • The variable speed controller has finger-tip dial action, digital system status with warning protection. • To start, press power switch on controller and spreader will accelerate to speed set on dial. • To stop, press power switch on controller to off position. • Adjust speed of spinner by using dial on right side of controller. • If audible beeping occurs, read the sequence and refer to page 21. Fast-Cast 4000 • The Dual Variable Speed Control has dual finger-tip dials for maximum performance, digital system status with warning protection and built-in Vibrator Switch. • To start, press power switch on controller and spreader will accelerate to speed set on spinner and auger dials. • To stop, press power switch on controller to off position. • Speed of auger and spinner may be adjusted separately to get desired flow and spread distance from spreader. • The Vibrator Switch is needed for dense material or to increase the flow to the Auger. This eliminates bridging of material. • A Material Baffle (Part #1CS4P19) has been installed in your spreader to stop fine material from free-flowing. If using dense or damp material, or if more flow is desired, remove Material Baffle. However, it is recommended that the Material Baffle remain inplace if using bulk salt. • It is important that the Inverted Vee (Part #1CS4P18) not be removed except when servicing. • If audible beeping occurs, read display to identify problem. If display reads “OL” (overload) or “OH” (overheat). Shut controller down and carefully clear jammed auger. If display reads “E1“ this means there is a dead short in system. Do not use until problem is corrected. If display reads “E 0” this means that the motor is not getting any power. Check all connections. If display reads “LB” the vehicle battery is extremely low and could damage system. • If there are any problems while operating the spreader, refer to Troubleshooting Guide on page 21. August 2001 1167 TRACTOR CAB INC. Fast-Cast 175 Schematic Assembly GATE DECK - CABLE ASSEMBLY MOTOR - TRANSMISSION ASSEMBLY Item No. Part No. Description Qty. 1CS1P8 3/8'' - 16'' x 1'' Hex Bolt 10 1CS1P9 3/8'' - Locknut 10 1CS1P41 3/8'' Flat Washer 2 1SM1P3 2-5/16' Hair Pin Clip 1 1SM1P2 5/8'' x 5-1/2'' Hitch Pin 1 1CS2P15 3/8'' Fender Washer 4 1CS1P53 Transmission 1 1CS1P25 1/4'' - 20 x 3/4'' Stainless Hex Bolt 4 1CS1P24 5/16'' - 18 x 1/2'' Hex Bolt 1 1CS1P30 1/4'' Stainless Lock Washer 4 1CS1P27 #10 - 32 x 5/8'' Hex Machine Screw 2 1CS1P28 #10 - 32 Lockwasher 2 1SM5P1 5/16'' Lock Nut 6 1CS1P46 5/16'' Lockwasher 1 1CS2P21 5/16'' Flatwasher 4 1CS1P7 5/16'' - 18 Hex Nut 1 1CS1P18 10'' Steel Spinner 1 1CS1P51 Motor Drive Coupler 1 1CS2P2 T-Handle Cable - 10' 1 1CS2P16 Bulkhead Cable Fitting 1 1CS2P17 5/16'' - 16 x 3/4'...
Ce manuel est également adapté pour les modèles :Outils de jardin - 175 (455.92 kb)
Outils de jardin - 3000 (455.92 kb)
Outils de jardin - 4000 (455.92 kb)