Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
STATUS LED STATUS GREEN Everything functioning normally . BLINKING ES, SES, or BPV detected YELLOW Loopbacks active . BLINKING In-band loopbacks armed RED Alarm on the HDSL2 loop, DSX or DS1 interface . BLINKING Signal Quality of 0 or No Sync on the HDSL2 loop FOUR-CHARACTER DISPLAY (FCD) OPERATION FCD Modes Mode Message Function Status STAT Displays loop margin, alarms, and general status conditions Display Off Blank Blank after five minutes of no activity View VIEW View current options settings Loopback LPBK Select and execute HDSL2 circuit loopbacks Status/Alarm Display (“STAT”) Message Description MARG xx HDSL2 loop margin, 0-20 DSL ERR CRC error detected on HDSL2 Loop LOC ERR Frame bit error (SF Mode), Bipolar Violation (BPV), or CRC error (ESF Mode) detected locally at DSX-1 of the H2TU-C REM ERR Frame bit error (SF Mode), Bipolar Violation (BPV), or CRC error (ESF Mode) detected remotely at DS1 of the H2TU-R DSL LOS No synchronization of H2TU-C and H2TU-R on loop LOC LOS DSX signal is absent from the network interface or is of a format which does not match the provisioning of the HDSL2 circuit REM LOS DS1 signal is absent from the network interface or is of a format which does not match the provisioning of the HDSL2 circuit ARM NIU Loopback is armed Left = MODE Center = OFF Right = SELECT COMPLIANCE CODES This product is intended for installation in restricted access locations only and in equip- ment with a Type “B” or “E” installation code. Input current at maximum load is 0.7 A at –48 Vdc. Maximum output at over current condition is 165 mA at –190 Vdc. WARRANTY Warranty for Carrier Networks products manufactured by ADTRAN and supplied under Buyer’s order for use in the U.S. is ten (10) years. For a complete copy of ADTRAN’s U.S. Carrier Networks Equipment Warranty: (877) 457-5007, Document #414. CODE IN OUT Installation Code (IC) A – Telecommunication Code (TC) – X Power Code (PC) F C Option Settings Display (“VIEW”) Message Description Settings Default LBO Line Build Out EXT, 0, 133, 266, 399, 533 * CODE Line Code AMI, B8ZS B8ZS FRMG DSX-1 Framing AUTO, UNF UNF NLBK NIU Loopback EN, DIS EN LBTO Loopback Timeout NONE, 1 Hr, 2 Hr, 8 Hr, 24 Hr 1 Hr CLOS Customer Loss Response AIS, LPBK AIS PRM Performance Reporting Messages NPRM, SPRM, NONE, AUTO AUTO TXLV DS1 Transmit Level 0 dB, -7.5 dB, -15 dB 0 dB SPWR Span Power EN, DIS EN ALMP Alarm Pattern to Customer AIS, LOS AIS * 220 = EXT, 3192/DDM+ = 0 Loopback Options Display (“LPBK”) Select Loopback State Loopback Description HTUC NET Network loopback at H2TU-C CST Customer loopback at H2TU-C NONE No active loopback HTUR BLB Bidirectional loopback at H2TU-R NET Network loopback at H2TU-R CST Customer loopback at H2TU-R NONE No active loopback DSX-1 BANTAM JACKS EQ ¦ Provides an intrusive access point to the data stream. TX - Access the data stream being received from the network. RX - Access the data stream being transmitted to the network. MON ¦ Provides a non-intrusive access point to the data stream. TX - Monitors the data stream being received from the network RX - Monitors the data stream being transmitted to the network. NOTE: The DDM+ H2TU-C does not have the DSX-1 Bantam Jacks option. RS-232 DB-9 CONNECTOR ¦ Used to access performance monitoring data, perform loopbacks and provision units via VT100 emulation applications such as Hyper Terminal – Private Edition, ProComm Plus, and Telnet. ¦ There are two types of terminal emulation modes, Manual and Real-Time. Use “CTRL-T” to toggle between the two modes. Manual Emulation Mode: Press the space bar 3 times to manually update the screen. Print screen and log file commands are available in this mode. Real-Time Emulation Mode: The default mode. Print screen and log file commands are not available in this mode. Cursor placement and screen highlighting are enabled. ¦ Provision terminal port as follows: Data Rate — 1.2 to 19.2 kbps Asynchronous Data Format — eight data bits, no parity (none), one stop bit ¦ When using a PC with terminal software, be sure to disable any power saving programs. PROVISIONING NOTES ¦ This unit c...
Ce manuel est également adapté pour les modèles :Matériel de réseau - 3192 H2TU-C (333.86 kb)