Supporting any mix of traffic, from all-circuit to all-packet, it is ideal for use where TDM and Ethernet services coexist. 2 Alcatel-Lucent 1850 TSS-5 Transport Service Switch The Alcatel-Lucent 1850 TSS Family New bandwidth-hungry services, such as triple play and Ethernet virtual private networks (VPNs), are placing great demands on the existing transport infrastructure. To remain profitable, businesses and service providers are embracing these new revenue-generating services by moving from c

The following example command configures a BGP peering session using a Loopback0 IP interface address: -> ip bgp neighbor 2.2.2.2 update-source Loopback0 See the OmniSwitch 7700/7800/8800 Advanced Routing Configuration Guide for more information. Chapter 22, “Configuring 802.1X” Quick Steps for Configuring 802.1X On page 22-3 the following two new steps should be added to this section: 6 (Optional) Configure a guest VLAN for the 802.1x port using the 802.1x guest-vlan command. -> 802.1x 3/1 gues

C September 2005 OmniSwitch 6624/6648/ 6800/7700/7800/8800 Troubleshooting Guide OmniSwitch Troubleshooting Guide September 2005 This troubleshooting guide documents OmniSwitch 6624/6648/770/7800/8800 hardware, including chassis and associated components, and Release 5.1 software. The specifications described in this guide are subject to change without notice. Copyright © 2006 by Alcatel Internetworking, Inc. All rights reserved. This document may not be reproduced in whole or in part without th

Dshell commands should only be used by Alcatel personnel or under the direction of Alcatel. Misuse or failure to follow procedures that use Dshell commands in this guide correctly can cause lengthy network down time and/or permanent damage to hardware. • Use the command udprelay_do_systrace = 0 to disable systrace and enable console output. • Use the command C = x (where x=1 to 9.) This increases the levels of udprelay debug. A level of 5 will display the source, destination IP, and MAC lines se

Null Route to IPMRM V2 192.168.13.25-255.255.255.255 dvmrpRecvIpmrmSGInfo: V2 Lookup ipsa 192.168.13.25 ipda 224.2.178.69, tsrc 0.0.0.0 Found route 192.168.13.0 to ipsa Route looks good Lookup S,G 192.168.13.25-255.255.255.255 224.2.178.69 on rib dvmrpRecvIpmrmSGInfo: V2 S,G found 192.168.13.25 224.2.178.69 Prune state pending, send another Prune dvmrpSendPrune: Learned S,G from non-local route, upstrGw=192.168.11.2 dvmrpSendPrune: Unable to find nbr for Prune. Null Route to IPMRM V2 192.168.13.

ipv6 dad-check ipv6_address if_name Syntax Definitions ipv6_address IPv6 address. ip_name Name assigned to the interface. Defaults N/A. Platforms Supported OmniSwitch 6624, 6648, 7700, 7800, 8800 Usage Guidelines The switch performs DAD check when an interface is attached to the stack and its VLAN first enters the active state. Use this command to rerun a DAD check on an address that was marked as duplicated. Example -> ipv6 dad-check fe80::2d0:95ff:fe6a:f458/64 Test_Lab Release History Release

For more information on VLANs and router ports, see Chapter 21, “VLAN Management Commands.” • RIPng will support a maximum of 20 interfaces. Example -> ipv6 rip interface Test_Lab Release History Release 5.1.6; command was introduced. page 2-64 Release 5.1.6.R02 User Guide Supplement June 2005 IPv6 Commands ipv6 rip interface Related Commands ipv6 load rip Loads RIPng into memory. ipv6 rip status Enables/disables RIPng on the switch. ipv6 rip interface recv-status Configures IPv6 RIPng interface

debug 802.1q {slot/port | aggregate_id} Syntax Definitions slot The slot number to configure 802.1Q tagging. port The port number to configure 802.1Q tagging. aggregate_id The aggregate link number to configure 802.1Q tagging. Defaults N/A Platforms Supported OmniSwitch 6624, 6648, 7700, 7800, 8800 Usage Guidelines Retrieves debugging messages for the tagged port selected. Examples -> debug 802.1q 5Aggregate Status = aggregate up -> debug 802.1q 3/1Slot Status = slot up Port Status = port up GEN

As of March 2007, the Alcatel-Lucent 1540 family is being used by more than 70 service providers in 41 countries worldwide. More than 26 million equivalent lines have already been delivered — plain old telephone system (POTS), integrated services digital network (ISDN), leased lines and digital subscriber line (xDSL). The Alcatel-Lucent 1353 Litespan Management System (LMS) is the management component of the Litespan family, which offers cost-effective voice, data, high-speed Internet access (HS

C March 2005 Omni Switch/Router™ User Manual Release 4.5 An Alcatel service agreement brings your company the assurance of 7x24 no-excuses technical support. You’ll also receive regular software updates to maintain and maximize your Alcatel product’s features and functionality and on-site hardware replacement through our global network of highly qualified service delivery partners. Additionally, with 24-hour-a-day access to Alcatel’s Service and Support web page, you’ll be able to view and updat