Évaluations - , GPA: ( )

Instructions DeWalt, Modèle D28402N

Fabricant : DeWalt
Taille : 2.45 mb
Nom Fichier :

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Allow the grinder to run up to full speed before touching the work surface. Lift the tool from the surface before turning the tool off. Allow the tool to stop rotating before putting it down. PADDLE SWITCH (D28402, D28402N) CAUTION: Before connecting the tool to a power source depress and release the paddle switch (A) once [D28402: without depressing the lock-on button (J)] to ensure that the switch is off. Depress and release the paddle switch as described above after any interruption in power supply to the tool, such as the activation of a ground fault interrupter, throwing of a circuit breaker, accidental unplugging, or power failure. If the paddle switch is locked on, thelock-off lever (B) toward the back of turn the tool on, push the tool will start unexpectedly when it is reconnected. A B Tothe tool, then depress the paddle switch (A). The tool will run while the switch is depressed. Turn the tool off by releasing the paddle switch. WARNING: Do not disable the lock-off lever. If the lock-off lever is disabled, the tool may start unexpectedly when it is laid down. English English SLIDER SWITCH (D28110, D28112) CAUTION: Before connecting the tool to a power supply, be sure the switch is in the off position by pressing the rear part of the switch and releasing. Ensure the switch is in the off position as described above after any interruption in power supply to the tool, such as the activation of a ground fault interrupter, throwing of a circuit breaker, accidental unplugging, or power failure. If the switch is locked on when the power is connected, the tool will start unexpectedly. To start the tool, slide the ON/OFF switch (L) toward the front of the tool. To stop the tool, release the ON/OFF switch. For continuous operation, slide the switch toward the front of the tool and Lpress the forward part of the switch inward. To stop the tool while operating in continuous mode, press the rear part of the switch and release. LOCK-ON BUTTON (D28402) The lock-on button (J) offers increased comfort in extended use applications. To lock the tool on, push the lock-off lever (B) toward the back of the tool then depress the paddle switch (A). With the tool running, depress the lock-on button (J). The tool will continue to run after the paddle switch is released. To unlock the tool, depress and release the paddle switch. This will cause the tool to stop. JA B CAUTION: Allow the tool to reach full speed before touching tool to the work surface. Lift the tool from the work surface before turning the tool off. SPINDLE LOCK The spindle lock (C) is provided to prevent the spindle from rotating when installing or removing wheels. Operate the spindle lock only when the tool is turned off, unplugged from the power supply, and has come to a complete stop. Do not engage the spindle lock while the tool is operating because damage to the tool will result. To engage the lock, depress the spindle lock button and rotate the spindle until you are unable to rotate the spindle further. C Mounting and Using Depressed CenterGrinding Wheels and SandingFlap Discs MOUNTING AND REMOVING HUBBED WHEELS CAUTION: Turn off and unplug the tool before making any adjustments or removing or installing attachments or accessories. Before reconnecting the tool, depress and release the paddle switch to ensure that the tool is off. Hubbed wheels install directly on the 5/8"-11 threaded spindle. Thread of accessory must match thread of spindle. 1. Backing flange is retained to the grinder by an O-ring on the spindle. Remove backing flange by pulling and twisting flange away form the machine. 2. Thread the wheel on the spindle by hand. 3. Depress the spindle lock button and use a wrench to tighten the hub of the wheel. 4. Reverse the above procedure to remove the wheel. CAUTION: Failure to properly seat the wheel before turning the tool on may result in damage to the tool or the wheel. MOUNTING NON-HUBBED WHEELS CAUTION: Turn off and unplug the tool before making any adjustments or removing or installing attachments or accessories. Before reconnecting the tool, turn the switch on and off as previously described to ensure that the tool is off. 9 Depressed center Type 27 grinding wheels G must be used with included flanges. See page 6 of this manual for more information. G must be used with included flanges. See page 6 of this manual for more information. 1. Install the unthreaded backing flange D (G) on spindle (D) with the raised section (pilot) against the wheel. Be sure the backing flange recess is seated onto the flats of the pushing and twisting the flange before placing wheel. 2. Place wheel against the backing flange, centering the wheel on the raised section (pilot) of the backing flange. 3. While depressing the spindle lock button, thread the clamp nut (H) on spin- H dle. If the wheel you are installing is more than 1/8" (3.31mm) thick, place the threaded clamp nut on the spindle 1/4" WHEELS so that the raised section (pilot) fits into (6.35mm) the...