Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
Using the Sensor Pen Holder When connecting the sensor pen to the machine, attach the sensor pen holder to keep the sensor pen with the machine. The right side of the holder can be used to hold the touch pen. Sensor pen holder a Using the point end of the cleaning brush or the seam ripper point, remove the protective cap covering the hole on the right side of the machine. > Insert the point of the seam ripper or cleaning brush into the hole in the protective cap, and then lightly pull out the protective cap to remove it. b Firmly insert the sensor pen holder into the hole where the protective cap was removed. Sensor Functions (For models equipped with the sensor function) Basic operations B-53 CONNECTING THE SENSOR PEN c Set the sensor pen in the sensor pen holder with the pen tip pointing downward, and then connect the sensor pen to the machine. B-54 USING THE SENSOR PEN USING THE SENSOR PEN Using the Sensor Pen Hold the sensor pen, and then touch the point to be specified. When the tip of the sensor pen is pushed in, the position information is sent to the machine. When using the sensor pen, touch slowly and gently for the definite operation. Important Information about Sensor Pen The sensor pen emits the signal to the machine, and then the sensor pen receiver receives the signal to specify the position. aSensor pen receiver bSignal is waved out from the sensor pen 1) Touch: Touch a point with the sensor pen, then immediately lift up the pen. CAUTION 2) Long touch: Touching a point with the sensor • Do not insert any object into the sensor pen pen and holding it down for at least one second and the receiver, otherwise the machine may allows you to activate the functions that you just be damaged. selected. Note • Once a point is touched with the sensor pen IMPORTANT and the entered information is applied in the • Do not put your hand, the fabric or any object screen, perform the next operation. between the machine and the sensor pen, Repeatedly touching a point with the sensor otherwise the sensor pen receiver may not pen may prevent the information from being receive the ultrasonic wave. correctly read. • Do not use the machine close to any other unit • Do not drag the sensor pen tip on the which produces ultrasonic wave or a vibration machine, otherwise the sensor pen tip may sound, otherwise interference may occur. be chipped off. • If there is any problem with the guideline marker, the sensor function may not operate correctly. B 2 Sensor Functions (For models equipped with the sensor function) Memo • The sensor pen can be used to touch on the screen as a touch pen. Basic operations B-55 USING THE SENSOR PEN Calibrating the Sensor Pen Before using the sensor pen for the first time be sure to calibrate it to the screen. Doing so allows the machine to learn the position you usually hold a pen. Hold the sensor pen at a comfortable angle and then calibrate the machine according to the procedure below. Be sure to keep the sensor pen at the same angle while calibrating the first and second points. a Press . b Display page 3 of the settings screen. c Connect the sensor pen to the machine and then press . > The Sensor Function Calibration screen appears. d First touch the green dot marking on the needle plate cover using the sensor pen. * Touch on the needle plate cover. a Needle plate cover e Touch the second point at the center of the cross-hair using the sensor pen. * Touch on the point in the illustrations. a Embroidery unit USING THE SENSOR PEN f Press to finish the calibration. To repeat the calibration touch the first point again using the sensor pen, and continue with step e. B 2 * Press to return to the original screen without finishing the calibration. * Press to reset the calibration. Sensor Functions (For models equipped with the sensor function) Basic operations B-57 USING SENSOR FUNCTIONS IN “EMBROIDERY”/“EMBROIDERY EDIT” MODE USING SENSOR FUNCTIONS IN “EMBROIDERY”/“EMBROIDERY EDIT” MODE Before using the sensor functions, carefully read the procedure in “Embroidery” and “Embroidery Edit” to familiarize yourself with the machine operations. Specifying the Embroidering Position With the Sensor Pen By using the sensor pen, the embroidering position can be adjusted to the desired location. This function can be performed in either “Embroidery” or “Embroidery Edit” mode, but the procedure described below is performed in “Embroidery” mode. If the message “The carriage of the embroidery unit will move. Keep your hands etc. away from the carriage.” appears during the operation, ensure safety, and then press . a Turn on the machine. b Press (Embroidery)/ (Embroidery Edit). c Select the category for the pattern to be embroidered. d In the pattern selection screen, press the key for the pattern to be embroidered. e Press . f Hoop the fabric and attach the embroidery frame to the machine. > Refer to “Hooping the Fabric in the Embroidery Frame” on page E-13 and “ATTACHING THE EMBROIDERY FRAME” on page E-17. g ...
Ce manuel est également adapté pour les modèles :Machines à coudre - Innov-is BP2100 (13.13 mb)