Log:
Évaluations - 3, GPA: 4 ( )

Instructions Asko, Modèle 59A40003727

Fabricant : Asko
Taille : 2.25 mb
Nom Fichier : a57dded1-e6c3-05f4-d54d-9fbf6ed95df4.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


To position the loader, proceed as follows: • Start the tractor and carefully drive the tractor to position it along the right side of the front loader, facing in the opposite direction of the loader. IMPORTAN T: Stop the tractor engine. Set the tractor’s parking brake before leaving the operator’s seat. • Remove the four protective caps from the male couplers at the free ends of the hydraulic hoses. • Locate the color coded protective plugs in the female hydraulic couplers on the lower right side of the tractor, just in front of the right/rear tire. Refer to Figure 8. • Using the color coded plugs and matching color coded washers on the loader hoses to guide you, remove the plugs and connect each loader hose to the appropriate hydraulic coupler. Refer to Figure 8. NOTE: If for any reason the color coded plugs of the outlets and/or caps and washers of the hoses are unavailable or incorrect, follow the routing of each hydraulic hose/tube to the loader cylinders to determine the loader connection of each hydraulic line. Use the following information to determine the appropriate hose to hydraulic outlet connection. Working from the right side of the tractor, facing the hydraulic outlets, proceed as follows: Outlet #1 (lower left) - connect the hydraulic line from the piston ends of the bucket cylinders (roll back bucket). Outlet #2 (upper left) - connect the hydraulic line from the cylinder body ends of the bucket cylinders (dump bucket). Outlet #3 (upper right) - connect the hydraulic line from the piston ends of the boom cylinders (lower boom). Outlet #4 (lower right) - connect the hydraulic line from the cylinder body ends of the boom cylinders (raise boom). Figure 8 • Check for ties that may be installed end to end around both of the boom cylinders. Cut and remove the ties if present. IMPORTAN T: Re-start the tractor and perform the hydraulic test described below in “Checking Implement Control Lever Operation” to assure that all implement control lever movements result in the loader movements described. If loader movements do not respond correctly, turn the tractor’s engine off, set the parking brake and recheck all hydraulic connections as described above. Loader control movements must be correct before proceeding. IMPORTAN T: If you were unable to connect the pistons of the two bucket cylinders to the bucket rear mounting brackets as instructed earlier, use the tractor’s implement control lever to extend the pistons as needed and connect the cylinders now. WARNING : Use extreme caution when performing the loader boom cylinder charging procedure. NOTE: For packaging purposes the two boom cylinders are fully collapsed. This results in the loader masts being positioned beyond their normal vertical position, which causes the loader’s center of gravity to be shifted rearward of normal. Consequently the loader hitch arms may not pivot downward when initially extending the boom cylinders pistons. When performing the initial priming of the boom cylinders, it will be necessary to apply downward force on the front of the bucket (e.g.; placing weight on bucket shave plate; an assistant applying downward pressure on the bucket) to pivot the hitch arms downward and raise the loader masts. • While observing the hoses to ensure they do not become pinched or stretched, slowly and carefully move the implement control lever rearward to extent the boom cylinders. The loader hitch arms should pivot downward toward the ground and raise the bottoms of the masts. Base of Mast LH Mount Tubular Bar Loader Hitch Arms 2 1 3 4 Lower Boom (#3-Blue) Raise Boom (#4-Green) Dump Bucket (#2-Yellow) Curl Bucket (#1-Red) Hydraulic Outlets • Continue to carefully extend the boom cylinders (and roll back the bucket if necessary) until the center points of the support plates on the bottom of the loader hitch bracket at the front of loader hitch arms are resting on the ground (Refer to Figure 13). The support plates and bucket should be supporting the loader and the bottom of each mast should now be higher than the tubular bars of the loader mounts. • Stop the tractor engine and engage the parking brake. Disconnect the loader hoses from the hydraulic couplers by pushing inward the locking collars of the tractor’s female hydraulic couplers. • Start the tractor and drive to the rear of the front loader. Align with the opening between the loader masts, and slowly drive the tractor forward while guiding the bottoms of masts into the RH and LH mounts. • Stop the tractor engine and engage the parking brake. Checking implement Control Lever Operation The tractor’s implement control lever is used to control the movements of the loader. Perform the following test to make certain that the loader hydraulic hoses and tubes are correctly connected. All implement control lever movements should result in the loader movements described in this sub-section. • Using the color coded plugs and matching color coded washers on the loader hoses to guide you, remove ...

Ce manuel est également adapté pour les modèles :
Rondelles - 59A40003727 (2.25 mb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories