Log:
Évaluations - 3, GPA: 5 ( )

Instructions Beko, Modèle D1 7101 EM

Fabricant : Beko
Taille : 760.95 kb
Nom Fichier :
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


After cancellation, the symbol of the corresponding step at which the cancellation was made will remain lit and “End” label will appear on the screen. Program in rinse hold mode • This process is shown with the flashing Spin Symbol (Figure 3- 13c) and the lit up Standby Symbol (Figure 3-13k). If you wish to spin when the machine is in this mode: Adjust the spin speed. Press “Start/ Pause/Cancel” button (Figure 2-10). The program continues, pumps out the water and spins. Standby Symbol (Figure 3-13k) fades out and Start Symbol (Figure 3-13j) lights up. If you want to discharge the water only without spinning: Press “Start/Pause/Cancel” button (Figure 2-10). Standby symbol (Figure 3- 13k) will fade. Start symbol (Figure 3-13j) will light up. The program continues and only pumps out the water. End of program When the program is finished, the symbols of the relevant steps will remain lit up and the auxiliary function, spin and temperature data selected at the start- up of the program will remain selected. “End” label will appear on the screen. 6 Quick instructions for daily use Preparation 1. Turn the tap on completely. Check if the hoses are connected tightly. 2. Place the laundry in the machine. 3. Add detergent and softener. Starting 1. Press the “On/Off” button (Figure 2- 14). 2. Select the program and the temperature. 3. If desired: – select any auxiliary function, – adjust the spin speed, – set the time delay, 4. Close the loading door. 5. Press “Start/Pause/Cancel” button (Figure 2-10). The display shows the time remaining for the program to complete if time delay is not set. The display shows the time remaining for the program to start if the time delay is set. 6. Check if the Door Locked Symbol (Figure 3-13i) lights up on the screen. The Door Locked Symbol (Figure 3-13i) will light up if time delay is not set. The Door Locked Symbol (Figure 3-13i) will fade if time delay is set. Canceling a program 1. Press and hold the “Start/Pause/ Cancel” button (Figure 2-10) for about 3 seconds; the Start symbol (Figure 3-13j) will start flashing. 2. The machine can discharge all the water or can take in water for 3 times at most to cool down the clothes and complete discharging process. Adding more laundry • This is only possible under the following conditions: – during time delay, C You may add or remove laundry during the time delay (until the program starts). At the beginning of a washing cycle (machine allows adding more laundry during a future step only if the water level is low enough to open the loading door or if the temperature in the machine is low). In order to add laundry after the start-up of the program: 1. Press “Start/Pause/Cancel” button (Figure 2-10). 2. Open the loading door and put in more laundry. 3. Close the loading door. 4. Press “Start/Pause/Cancel” button (Figure 2-10). Program is in rinse hold mode C This process is shown with the flashing spin symbol (Figure 3-13c) and the standby symbol (Figure 3- 13k) which is lit up. If you wish to spin when the machine is in this mode: 1. Adjust the spin speed. 2. Press “Start/Pause/Cancel” button (Figure 2-10). The program continues, pumps out the water and spins. 3. The standby symbol (Figure 3-13k) fades out and the start symbol (Figure 3-13j) lights up. If you want to discharge the water without spinning: 1. Press “Start/Pause/Cancel” button (Figure 2-10). 2. The standby symbol (Figure 3-13k) fades out and the start symbol (Figure 3-13j) lights up. 3. The program continues and only pumps out the water. Re-spinning the laundry The control system for an unbalanced load can pause the spinning in cases when the distribution of the laundry in the drum is not balanced. If you want to re-spin the clothes: 1. Distribute the laundry in your machine for a balanced load. 2. Select the spin program. 3. Adjust the spin speed. After the program is finished Program indicator symbols (Figure 3- 13f) on the screen will remain lit after the program is finished. “End” will appear on the screen. 1. Open the loading door and take out the laundry when the door locked symbol on the display (Figure 3-13i) fades out. 2. Press the “On/Off” button (Figure 2- 14). 3. Turn the water tap off. 4. Remove any folds in the rubber seal on the loading door and check for debris. 5. Leave the loading door and detergent drawer open to dry. 7 Cleaning and care Detergent drawer Remove any powder residue buildup in the drawer. To do this; 1. Press the dotted point on the siphon in the softener compartment and pull towards you until the compartment is removed from the machine. C If more than a normal amount of water and softener mixture starts to gather in the softener compartment, the siphon must be cleaned. 2. Wash the dispenser drawer and the siphon with plenty of lukewarm water in a washbasin. Wear protective gloves or use an appropriate brush to avoid touching the residues in the drawer when cleaning. 3. Replace the drawer into its housing after cleaning. Check if the siphon is in i...

Ce manuel est également adapté pour les modèles :
Rondelles - D1 7082 E (760.95 kb)
Rondelles - D1 7081 E (760.95 kb)
Rondelles - D1 7101 E (760.95 kb)
Rondelles - D1 7102 E (760.95 kb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories