Log:
Évaluations - 2, GPA: 4 ( )

Instructions American Dryer Corp., Modèle AD-200 Tilting

Fabricant : American Dryer Corp.
Taille : 5.84 mb
Nom Fichier : 11c790e7-32f1-41c8-93b6-75db8a4525d6.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


70-LATEST EDITION. A. REASSEMBLY OF DRYER IMPORTANT: Always keep the tumbler (basket) section of the dryer in an upright position when moving it. The AD-200 dryer may be shipped one of two ways; as a complete unit fully assembled and ready for hookup or with the tumbler (basket) section separated from the base. If the dryer is shipped in two (2) pieces, the tumbler (basket) section will have to be lifted onto the base. Use cables through the eye bolts on top of the tumbler section, or use a fork lift for the lifting process. The AD-200 Tilting dryer is made in many loading and unloading options. Please refer to the reassembly instructions on the following pages for your particular style of dryer. If a steam dryer is shipped in two (2) pieces, the steam coil may have been removed from the top of the tumbler (basket) section and shipped with the base. If this is the case, lift the steam coil on to the top of the tumbler section with the steam pipe connections facing towards the right side of the dryer and bolt the coil to the top of the dryer with the 1/4" hardware supplied. There are three (3) panels that cover the front, right side, and rear of the steam coil. Fasten these in position also. Reconnect the steam and condensate pipe unions to the coil. These pipes run down to the flex hoses in the base. 10 1. Reassembly Instructions For Gas Drver Shipped In Two Pieces FRONT VIEW RICHT S®E VIEW MAN2241 11 PISTON RECONNECTION VIEWQ) BOTTOM OF TUMBLER SECTION PISTON CLEVIS BLOCK RETAINING RING ■PIN PISTON ROO EYE TILTING PISTON ATTACH CHAIN TO SECOND -BACK PANEL SCREW BELOW SEAM GAS FLEX HOSE UNION RECONNECTION VIEW(D чех hose must hot be kngo REAR TILT GUARD -«CCMtfCr Г* (MN 12 a. Reassembly For 1-Door/2-Way Tilt Gas Dryers; Lift the tumbler (basket) section onto the base. 1) 2-Way Tilt dryers have four (4) tilting pistons in the base, one (1) on each comer. On the top of each piston is a clevis block. Use the four (4) 1/2" diameter x 1-1/8" long hex head bolts with lock washers to secure each piston clevis block to the bottom of the tumbler section. (Refer to the [top] View 1 on the previous page fpage 121.1 2) The flexible gas hose union is disconnected when the dryer is shipped in two (2) pieces. The flexible gas hose is located in the right side of the base. Insert the flexible hose with the union half up through the hole on the bottom of the tumbler section and retighten the union. The flex hose must not be kinked. (Refer to [center] View 2 on the previous page [page 12].) 3) There are two (2) electrical reconnections: a) A plug and cable is located in the right side of the base. This must be lifted up and reconnected into the mating socket located at the bottom of the right tumbler section. b) The drive motor wires must be lifted up from the base and reconnected into the junction box next to the tumbler drive motor in the left side of the tumbler section. Make sure both reconnected cables have enough slack in them to allow the dryer to tilt freely in both directions. 4) Reattach the tilt guard panels: a) Use the 1/4-20 x 3/8" hex head bolts with lock washers to bolt the top of the front tilt guard up into the bottom of the front of the tumbler section. b) Use 1/4" self-tapping screws to secure the side tilt guards on the top sides of the base. c) Use 1/4" self-tapping screws to secure the rear tilt guards on the rear of the base. Reconnect the spring and claw assembly which connects the rear tilt guard to each side tilt guard. (Refer to [bottom] View 4c on the previous page fpage 121.) This spring keeps the rear tilt guard close to the dryers back as the dryer is tilted forward and back. 5) Secure the 20" diameter exhaust duct transition piece to the dryers' rectangular exhaust duct with the 1/4-20 self-tapping screws supplied with the dryer. The exhaust duct exits from the rear of the base. 6) On dryers equipped with an automatic (piston operated) load door, reconnect the two (2) poly flow air lines that run from the base up to the door pistons. 13 2. Reassembly Instructions For Gas Drver Shipped In Two Pieces ADG-2001-Door / Forward Tilt FRONT VIEW RIGHT SIDE VIEW MAN22*0 14 PISTON RECONNECTION VIEW© -BOTTOM OF TUMBLER ADG-2001-Door / Forward Tilt GAS FLEX HOSE UNION RECONNECTION VIEW Q) '«COMCCr xmxxfl nsx nose **r not x knoo HINGE RECONNECTION VIEW(to) a. Reassembly For 1-Door/Forward Tilt Gas Dryers; Lift the tumbler (basket) section onto the base. 1) Forward Tilt dryers have two (2) tilting pistons in the rear of the base. On the top of each piston is a clevis block. Use the two (2) 1/2" diameter x 1-1/2" long hex head bolts with lock washers to secure each piston clevis block to the bottom of the tumbler section. (Refer to the [top] View 1 on the previous page fpage 151) a) Reattach the two (2) base tilting hinges in the front of the dryer to the tumbler section using the 1/2" x 1-1/2" hex head bolts and lock washers supplied. (Refer to [cen...


Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories