CLEANING THE HEAT EXCHANGER FILTERS If the applicable indicator (clean the heat exchanger filters) is on, the filters must be cleaned. ENGLISH 21 To clean the filters: 1. Open the loading door. 2. Move the release button on the bottom of the door opening and open the heat exchanger door. 3. Turn the blockage to unlock the heat exchanger cover. 4. Lower the heat exchanger filters cover. 5. Lift the primary filter. Hold the heat exchanger filter and pull it out from the bottom compartment. 6. Push

WARNING! Do not use standard bulbs! These develop too much heat and may damage the machine! Before replacing the bulb, disconnect the mains plug; with a permanent connection: fully unscrew or deactivate the fuse. 1. Unscrew cover above the bulb (this can be found directly behind the loading aperture, at the top; refer to “Description of machine” section.) 2. Replace defective bulb. 3. Screw cover back down. Check the correct positioning of o-ring gasket before screwing back the door light cover.

Press the START PAUSE button sequentially until you set desired level. 4. To memorize setting press simultaneously the DELI- CATE and TIME buttons or turn knob to OFF position Emptying water tank - warning mes- sage permanent off When using an external drain for the condensed water. 1. Turn the programme selector to any programme. 2. Press simultaneously the LONG ANTI-CREASE and TIME buttons and hold down for approx. 5 seconds. The current setting is on the display: – - led warning is permanentl

on the display. ENGLISH 19 TROUBLESHOOTING TROUBLESHOOTING Problem1) Possible cause Remedy The tumble dryer is not connected to mains supply. Connect in at mains socket. Check fuse in fuse box (domestic installation). The tumble dryer does not operate. The loading door is opened. The On/Off button was not pushed. The Start/Pause button was not pushed. Close the loading door. Push the On/Off button. Push the Start/Pause button. The appliance is in the standby mode. Push the On/Off button. Incorre

During this sequence the alternately reversing tumbling action of the drum continuously loosens the laundry so that it remains fluffy and crease-free until taken out. When the anti-crease programme has ended, I automatically switch myself off. You should remove your laundry from my drum by this time to avoid creasing. Programme end Switching off You switch me off by turning my programme selector switch to the the machine 0 position. My drum lighting is then also switched off. My operating indi

The machine may otherwise be damaged. • Before starting up for the first time, ensure that the nominal voltage and type of current specified on the machine type plate match the nominal voltage and type of current at the installation site. The electrical fuses required can also be found on the type plate. • Always connect the plug into a protection contact socket which has been installed as specified. • With permanent connections: A permanent connection may only be established by an authorised sp

We therefore recommend that you adopt the following guidelines: • cotton, linen: drum full but not too tightly packed; • synthetics: drum no more than half full; • delicate fabrics: drum no more than one third full. Hints & Tips on drying Hints & Tips on Drying Care symbols Before placing articles of laundry in your tumble dryer, check the care labels to ensure they are recommended for tumble drying. Basically, this fabric can be tumble dried; however the manufacturer does not specify whether it

EO/7). 8. Slide the chimney cover plate (Fig. EO/2) (with the lateral ventilation grille) (Fig. EO/8) from the front on to the fume extractor hood until it engages the holders in the RH and LH sides. Firmly press upwards against the chimney equalizer (connection by double adhesive tape). 9. Fix chimney cover plate (Fig. EO/2) laterally with 4 2.9 x 6.5 mm sheet metal screws on the chimney retaining plate. Additional installation work for return air operation Installation steps same as for e

EW) from the appliance every 6 — 8 weeks and wash it by hand or in your dishwasher. The active carbon filter must be changed not later than after 1 year. The active carbon filter cannot be washed or regenerated. Good deodorization is conditional upon a suitable active carbon volume (depending on the air capacity of your fume extractor hood) and specific arrangement of the active carbon filter in your fume extractor hood. This combination ensures a positive return air supply in contrast to ex

non-flammable exhaust air hose (E-No. 610899088) (for your own account from our range of special accessories). The exhaust air connection has a theoretical opening of 125 mm dia. Exhaust air discharged upwards or backwards: The exhaust air can be discharged through the available moving hose (accessory) with a sleeve inside the chimney cover plate (Fig. EO/2) upwards or directly backwards (wall box). Preparing for exhaust air operation 35 Wall Installation steps for exhaust air operation mou