Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
ESAB 230/460 vac, 3 ph., 60 Hz 453cc - 0558001274 553cc - 0558001278 ESAB 230/460/575 vac, 3ph., 60 Hz 453cc - 0558001275 553cc - 0558001279 ESAB 220/400 vac, 3 ph., 50 Hz 453cc - 0558001276 553cc - 0558001280 ESAB 220/400 vac, 3 ph., 50 Hz, CE 453cc - 0558001277 553cc - 0558001281 These INSTRUCTIONS are for experienced operators. If you are not fully familiar with the principles of operation and safe practices for arc welding equipment, we urge you to read our booklet, "Precautions and Safe Practices for Arc Welding, Cutting, and Gouging," Form 52 529. Do NOT permit untrained persons to install, operate, or maintain this equipment. Do NOT attempt to install or operate this equipment until you have read and fully understand these instructions. If you do not fully understand these instructions, contact your supplier for further information. Be sure to read the Safety Precautions before installing or operating this equipment. USER RESPONSIBILITY This equipment will perform in conformity with the description thereof contained in this manual and accompanying labels and/or inserts when installed, operated, maintained and repaired in accordance with the instructions provided. This equipment must be checked periodically. Malfunctioning or poorly maintained equipment should not be used. Parts that are broken, missing, worn, distorted or contaminated should be replaced immediately. Should such repair or replacement become necessary, the manufacturer recommends that a telephone or written request for service advice be made to the Authorized Distributor from whom it was purchased. This equipment or any of its parts should not be altered without the prior written approval of the manufacturer. The user of this equipment shall have the sole responsibility for any malfunction which results from improper use, faulty maintenance, damage, improper repair or alteration by anyone other than the manufacturer or a service facility designated by the manufacturer. PREFACE The purpose of this manual is to provide the operator with information required to install and operate the power source. Some technical reference material is also provided to assist in basic troubleshooting the power source. If it is determined that the power source is not operating properly, the operator should contact ESAB at (843) 664-4416 for assistance. The following is a list of terms/acronyms used throughout this manual. CC Constant Current CV Constant Voltage GMAW Gas Metal Arc Welding, CV mode (same as MIG) GMAW-P Gas Metal Arc Welding - Pulsed, CV mode (same as pulsed MIG) GTAW Gas Tungsten Arc Welding, CC mode (same as TIG) MIG Metal Inert Gas, CV mode (same as GMAW) SMAW Shielded Metal Arc Welding, CC mode (same as Stick) Stick Stick Welding, CC mode (same as SMAW) TIG Tungsten Inert Gas, CC mode (same as GTAW) 2 TABLE OF CONTENTS SECTION PARAGRAPH TITLE PAGE SAFETY ENGLISH SAFETY PRECAUTIONS ................................................................................................................ 4, 5 FRENCH SAFETY PRECAUTIONS ................................................................................................................ 6, 7 SECTION 1 DESCRIPTION..................................................................................................................................... 8 1.1 General ................................................................................................................................................ 8 1.2 Receiving-Handling .............................................................................................................................. 8 1.3 Description ........................................................................................................................................... 8 1.3.1 Power Source ...................................................................................................................................... 8 1.3.2 Volt-Ampere Characteristics ................................................................................................................ 9 1.4 Optional Accessories ........................................................................................................................... 9 1.5 Safety ................................................................................................................................................... 9 SECTION 2 INSTALLATION ...................................................................................................................................10 2.1 Location ...............................................................................................................................................10 2.2 Receiving, Unpacking and Placement.................................................................................................10 2.3 Primary (Input) Electrical Connection .....................................................................................
Ce manuel est également adapté pour les modèles :Machines à souder - 553cc (2.75 mb)