Évaluations - 2, GPA: 4.5
(
)
)
|
Facilité d'utilisation
4 SETUP PROJECTION MIRROR Remove the 4 Protection Pads inside of the Top Cabinet and remove the 2 Fixing Bands (right and left) of the Projection Mirror. Remove the 8 Screws(A) of the Mirror Arms. Lift the Projection Mirror and raise the Mirror Arms backward. Loosen the Screws(B) on the end of the Mirror Arms. Put the Mirror Holder between the Adjusting Nut and the Washer at each side of the Mirror. And then fix the Mirror Holders on the Mirror Arms with the Screws(B) temporary. Fix the Mirror Arms on the Cabinet with the Screws(A). Fix the Projection Mirror to the end of the Mirror Arms with the Screws(B) securely. Preparation Set Mirror Arms Fix Projection Mirror 1 2 3 CAUTION NEVER TOUCH THE PROJECTION MIRROR DIRECTLY. IT MAY EFFECT THE PROJECTION IMAGE QUALITY. MOVE THE MIRROR BY HOLDING THE MIRROR HANDLE. BE SURE TO REMOVE ALL THE PROTECTION PADS FROM THE CABINET. Projection Mirror Fixing Bands Projection Mirror Fixing Bands (2 pcs) Screws(A) (4 pcs X 2) Mirror Arm Mirror Handle Screws(A) (4 pcs X 2) Mirror Arm Screw(B) Protection Pads (4pcs) Adjusting Nut Screw(B) Washer Mirror Arm Mirror Holder 5 ADJUST PROJECTION MIRROR When the figure of the projection image does not match the Projection Screen, adjust the Projection Mirror. If the figure fits the Projection Screen precisely, skip the steps 2, 3 and 4 and replace the Back Cover. Connect the projector to the AC outlet, and turn the projector on. Connect the video output equipment to the projector. Project the image of cross-hatch or circles to check whether the picutre is displayed fully on the Projection Screen and is not distorted. (Refer to the Owner's Manual for operation.) If the figure is distorted, adjust the Projection Mirror following the steps 2 to 4 below. If the picture is displayed properly, adjustment of the Mirror is not required. Skip the steps below and replace the back cover. Adjust the Projection Mirror by turning the Adjusting Nuts. Move the Projection Mirror up or down by turning the Adjusting Nuts on the both sides of the Projection Mirror. Adjust Screw(B) if it required. Refer to the figure on the right for the image movement with the Adjusting Nut. Fix the Projection Mirror where the picture is displayed properly. Fix the Screw(B) securely. When fixing the Screw(B) the figure may be distorted again. When it should happen, readjust the Mirror following the steps 2 to 4. Check Projection Image Adjust Projection Mirror Fix Projection Mirror 1 2 3 CAUTION DO NOT STARE DIRECTLY INTO THE LENS. EYE DAMAGE COULD RESULT. WHEN ADJUSTING THE MIRROR, NEVER TOUCH THE PARTS EXCEPT THE MIRROR. IT MAY RESULT IN ELECTRICAL SHOCK. Turn off the projector and disconnect it from the AC outlet. Turn the projector off 4 Adjusting Nut Screw(B) Mirror Holder Mirror Arm Lower the Mirror Holder. Lift the Mirror Holder. Turn Adjusting Nuts to adjust the screen image. When turning the Adjusting Nuts on both sides to the right, the lower part of the image becomes narrow. When turning the Adjusting Nuts on both sides to the left, the lower part of the image is stretched. When turning the Adjusting Nuts on one side to the left or the right, one side of the lower part of the figure is shortened or stretched. 6 ASSEMBLE STORAGE SPACES Replace the Back Cover to the Top Cabinet. Turn the Back Cover over, and fix the cover in the reverse to the initial position. Replace Back Cover 1 Back Cover Screws (14 pcs) IInsert the Shelves' Pins into appropreate position of the walls of Storage Spaces. Install the Compartment Shelves in Storage Spaces. 1. Remove the Hinge Covers by removing the 2 screws of each Hinge. 2. Hold the Glass Doors between the Glass Hinges and the Hinge Covers. Install the Glass Doors so that the side with the Holder Magnet is matched to the magnet inside of the Storage Spaces. Do not install the Glass Doors in the reverse. Tighten the screws and fix the Glass Doors. 1. When adjusting the position of the Glass Doors, loose the Screws(A) and move the Glass Doors with the Hinges to the arrow direction until the surface of the door matches to the surface of the Cabinet Front. 2. When adjusting the tilt of the Glass Doors, adjust the Screws(B) (lower and upper) and move the Glass Doors. Install Glass Doors Adjustments of Doors Install Compartment Shelves 2 3 4 Holder Magnet Screws (2pcs x 4) Glass Door Screw(A) Screw(B) Shelves' Pins (4 pcs X 4) Compartment Shelves (4 pcs) Holder Cover 7 LOCK CABINET 1 CAUTION BE SURE TO LOCK THE CABINET WITH LOCK BOLTS PROPERLY. IF THE CABINET IS NOT LOCKED, CABINET IS UNSTABLE AND MAY FALL DOWN. Lock the Cabinet Turn Lock Bolts to the direction indicated on the figure to lock the cabinet on the floor. Make sure that all the Casters are slightly raised from the floor. The tilt of Cabinet can be also adjusted with these Lock Bolts. Lock Bolt Lifting the cabinet up to settle it. Cabinet Dimensions ( W x H x D ) : 1532 mm (60.3") x 1968mm (77.5" ) x 747mm (29.4" ) Net Weight : 145kg (319.7lbs ) Letting the cabinet down...
Ce manuel est également adapté pour les modèles :TV - 1AA6P1P1756 (114.85 kb)