Évaluations - 2, GPA: 3.5
(
)
)
|
Facilité d'utilisation
This system is supplied in 3 packages and they need to be installed. Please make sure all the parts are included. If any part is missing, or if you have questions, contact a sales dealer. Install the system following steps. 1. CHECK CONTENTS IN PACKAGES 2. ASSEMBLE BOTTOM CABINET 3. JOINT TOP AND BOTTOM CABINETS 4. SETUP PROJECTION MIRROR 5. ADJUST PROJECTION MIRROR THIS SYSTEM MUST BE INSTALLED BY 2 OR MORE PEOPLE 6. ASSEMBLE STORAGE SPACES 7. LOCK CABINET CAUTION WHEN INSTALLING THIS SYSTEM, BE CAREFUL NOT TO DAMAGE THE PROJECTION SCREEN. AND NEVER TOUCH THE SURFACE OF THE PROJECTION SCREEN AND THE PROJECTION MIRROR DIRECTLY. THEY MAY EFFECT THE PROJECTION IMAGE QUALITY. BE CAREFUL NOT TO DROP ANY PART OR TOOL LIKE SCREW INTO THE SYSTEM. IF IT SHOULD, CONTACT A SERVICE. EXCEPT WHEN ADJUSTING THE PROJECTION MIRROR, NEVER TURN THE SYSTEM ON UNTIL THE INSTALLATION IS FINISHED. IT MAY CAUSE ELECTRICAL SHOCK OR FIRE HAZARD. 710-00792-1 1AA6P1P1756--(M8EA) 1 CHECK CONTENTS IN PACKAGES This system is supplied in 3 packages. Make sure all the parts listed below (cabinets, Installation parts, and accessories) are included in those packages. Top Cabinet : Refer to the steps 3 to 6 for installation. Center Panel -----------------------------------------1 Package 1 Package 2 Package 3 Bottom Cabinet : Refer to the steps 2, 6 and 7 for installation. Installation Part Owner's Manual ---------------------------------------1 Installation Manual (this brochure) ---------------* AC Power Cord ---------------------------------------* Wireless Remote Control Unit --------------------1 Wireless/Wired Remote Control Unit -----------1 Remote Control Cable -----------------------------1 Batteries for Remote Controls --------------------4 VGA Cable -------------------------------------------1 MAC/VGA Adapter ----------------------------------1 Mouse Cables (Serial, PS/2, ADB)---------------* The accessories marked (*) may not supplied or may be differ in quantity in some models. Refer to the Owner's Manual for details. Accessories Qty. Glass Doors -------------------------------------------2 Compartment Shelves -----------------------------4 Shelves' Pins -----------------------------------------16 Installation Parts Qty. Package 1 Package 2 Package 3 uActual packages may be differ from this figure in some models. 2 ASSEMBLE BOTTOM CABINET Remove the 4 Joint Bolts on the Bottom Cabinet. Keep these bolts for later use. They are necessary for joint the Top and Bottom Cabinets. Remove the 2 Cover Plates on the top of the Bottom Cabinet. Keep the Cover Plates for later use. Replace those plates, when the appliance needs to be transported. Install the Center Panel to the Bottom Cabinet. Be sure to meet the Center Panel and the Bottom Cabinet at the upper part first, and insert the 6 legs of Center Panel to the holes of the Bottom Cabinet. Be sure to set the Center Panel securely. Remove Joint Bolts and Cover Plates Install Center Panel 1 Cover Plates (2 pcs) Joint Bolts (4 pcs) Center Panel Meet the Center Panel and the Bottom Cabinet at the upper part first and push in the Panel securely. LegHole There are the 5 Protection Pads inside of the Bottom Cabinet for protection against shock or vibration. Remove the 4 Pads supporting at the upper side of the Bottom Cabinet first. And then, remove the pad(A) supporting at the lower side of the projector. When removing the pad(A), pull downward first and remove the pad. Remove Protection Pads CAUTION WHEN REMOVING THE PROTECTION PADS, BE CAREFUL NOT TO BROKE THE WIRING INSIDE OF THE BOTTOM CABINET. BE SURE TO REMOVE ALL THE PROTECTION PADS INSIDE OF THE CABINET. AND BE CAREFUL NOT TO LEAVE ANY PAD OR FRAGMENT IN THE CABINET. IT MAY RESULT IN FIRE HAZARDS. Joint Bolts (4 pcs) Protection Pads (5 pcs) The back side of the Bottom Cabinet. Pad(A) Pull the pad(A) to downward first and remove the pad. Projector 3 J0INT TOP AND BOTTOM CABINETS .................. Lift the Top Cabinet and put it on the Bottom Cabinet. When setting the Top Cabinet, be sure the frame of the Bottom Cabinet is fitted into the frame of the Top Cabinet completely. Remove the 14 Screws and the Back Cover. Keep the screws and Back Cover. All the installations are finished, all those parts should be replaced. Remove the Cover Plate on the lower part of the Top Cabinet. Keep the Cover Plate for later use. Replace this plate when the appliance need to be transported. Joint Top and Bottom Cabinets Remove Back Cover Remove Cover Plate 1 2 3 Joint the Top and the Bottom Cabinets with the 4 Joint Bolts securely. Fix the Cabinets4 CAUTION BE SURE TO FIX THE CABINETS WITH JOINT BOLTS. IF THE TOP AND THE BOTTOM CABINETS ARE NOT FIXED PROPERLY, THE TOP CABINET MAY BE DROPPED OR FALL DOWN. Screws (14 pcs) Bottom Cabinet Top Cabinet Be sure the frame of the Bottom Cabinet is fitted into the frame of the Top Cabinet completely. Bottom Cabinet Top Cabinet Joint Bolts (4 pcs) Joint Bolts (4 pcs) Cover Plate Frame CAUTION THE TOP CABINET OF TH...
Ce manuel est également adapté pour les modèles :TV - 710-00792-1 (114.85 kb)