Évaluations - 2, GPA: 3.5 ( )

Fabricant : Mitsubishi Electronics Taille : 2.67 mb Nom Fichier : Langue d'enseignement:

4. When I try to use the remote control, the POWER key blinks five times. Replace the batteries. 5. TV does not respond to the remote control or to control-panel buttons and TV will not power on or off. Unplug the AC power cord for 10 seconds. • Use the System Reset button. • 6. When a device is selected from the Input Selection menu, the screen is purple or black (no signal source). • Make sure the selected device is turned on. • Begin play of the device. 7. You have forgotten your Lock menu pass code. See Appendix B, “Bypassing the Parental Lock,” page 63. 8. Rating restrictions are not working. Open the Parental Lock menu and: • Verify that the U.S. Ratings or Other Ratings setting is On. • Check the Lock Time/Unlock Time to check if rating restrictions are disabled. • Rating restrictions apply only to content on ANT 1 and ANT 2, and VIDEO composite video jacks. 9. On-screen displays appear each time you change a function. Normal TV operation. 10. A warning message appeared on screen stating, “TV will shut down in a few seconds. Please check if the air flow is blocked.” • Room temperature has exceeded proper levels. Cool the room. • The TV has overheated. Clear blocked air vents and ensure at least four inches of clearance on all sides of the TV. • Clean the air filter on the lamp cartridge See page 80. Service and Customer Support Service If you are unable to correct a problem with your TV, consult your Mitsubishi dealer or Mitsubishi Consumer Relations at (800) 332-2119. • DONOTadjustanycontrolsotherthanthosedescribed in this Owner’s Guide. • DONOTremovetheprotectivebackcoverofyourTV. Customer Support • Toorderreplacementoradditionalremotecontrols, lamp cartridges, or Owner’s Guides, visit our website at or call (800) 553-7278. • Forquestions: Call Consumer Relations at 800-332-2119. E-mail: MDEAservice@mdea.com Website: Important All lamps replaced under warranty must be returned to Mitsubishi where they will be inspected for defect verification. TV Channels Symptom Remarks 1. The TV takes several seconds to respond to channel changes. • It is normal for digital channels to take longer to tune in. • Press ENTER after a entering channel number to avoid delays. • Use a 4-digit number for an over-the-air digital channel. • Use a 6-digit number for digital cable channels if your cable service is able to recognize 6-digit channel numbers. 2. You cannot access a channel. • Use number keys instead of CH / . • Be sure the channel you want to view is in memory. See Setup > Scan on page 42. • Check that the TV is switched to the correct device or antenna for that channel by pressing the INPUT key. • Make sure Channel Lock is off. • Make sure the Lock > Parent menu lock is set to off. • If you cannot tune to a virtual digital channel even though the TV has already memorized digital channels, tune to the physical channel number used by the broadcaster. The virtual channel will then be automatically added to memory. 76 Appendices Appendices 77 Appendix D: Troubleshooting, continued Appendix D: Troubleshooting, continued Appendices 77 Appendix D: Troubleshooting, continued Appendix D: Troubleshooting, continued TV Channels Symptom Remarks 3. Name options are not available for some channels. You can name only memorized analog channels and memorized digital channels not named by the broadcaster. 4. When ChannelView list is displayed, information appears incomplete • Available information is sent from the broadcaster or cable provider. No other data is available. • Make sure the TV clock is set correctly. TV Power On/Off Symptom Remarks 1. TV takes an excessively long time to power on. • When switched on, the TV needs time to boot up, just as a computer does. Also, the TV’s lamp requires a few moments to heat up to full brightness. • TV Energy Mode is set to Low Power. Change TV Energy Mode to Fast Power On in the Setup menu. 2. You cannot program the TV to turn on automatically (Timer function) • The TV may be locked. • The clock may not be set. • TV Energy Mode is set to Low Power. Change to Fast Power On in Setup menu. 3. The TV will not turn on after being plugged in. If light on front panel is blinking, wait at least one and a half minutes for the light to turn off, then press POWER again. 4. TV turned itself off and the light on the front panel started to blink. • Momentary power fluctuation caused the TV to turn off to prevent damage. Wait for the green light to stop flashing and turn the TV on again. • If the TV does not stay on, use the System Reset button on the control panel. If this happens frequently, obtain an AC line power conditioner/surge protector. • An unusual digital signal may have been received, triggering a protection circuit. Wait for the light to stop flashing and turn TV on. 5. TV turned itself off and the STATUS light is a steady yellow. • The TV has overheated. Clear blocked air vents and ensure at least four inches of clearance on all sides of the T...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :