Évaluations - 5, GPA: 4
(
)
)
|
Facilité d'utilisation
Unauthorized users cannot turn it off or change it. This feature is intended to discourage theft and provides a way to identify the projector should it be stolen. Enabling Password Protection To prevent unauthorized use, you can assign the projector a password. If you do, a screen will appear requesting the password whenever the projector is plugged in and turned on. If an incorrect password is entered three times in succession, the projector’s operation is locked and the power cord must be disconnected and reinserted to redisplay the password screen. If an incorrect password is entered thirty times in succession, the user must contact Epson to unlock the projector. Fine-Tuning the Projector The default setting for the Password Protect function is Off. Follow these steps to turn password protection on: 1. Press the Freeze button on the remote control for about five seconds. You see this screen: caution If you lose the remote 2. Use the pointer button to set Power On Protect to On. Then control, you will not be able press Enter. to enter the password. Keep the remote control in a safe 3. Press Esc. place at all times. 4. Select Password and press Enter. 5. When you see a message asking if you want to change the password, select Yes and press Enter. 6. Hold down the Num button on the remote control and use the numeric keypad to enter a four digit password. (The default setting is 0000.) 7. When you see a confirmation message, reenter the password. Then press the Menu button to exit the screen. 8. Press the Num button on the remote control to deactivate the numeric keypad. 9. If you want to disable the password temporarily, select Timer and press Enter. Then hold down the Num button while you use the numeric keypad to enter the number of hours (from 0 to 9999) that you want the password feature disabled. If you want the projector to request the password every time it is turned on, set the timer to 0H. Fine-Tuning the Projector 51 The countdown for the elapsed time begins as soon as you close the Password Protect menu. (You can check the elapsed time in this menu next to Time elapsed.) 10. To enable your screen logo, select User’s Logo Protect and press Enter. Select On and press Enter. When this feature is on, the logo appears whenever you turn on the projector (if the Startup Screen is enabled in the Extended menu; see page 53). It also appears when you press the A/V Mute button (if you selected the Logo for the A/V Mute setting under Display in the Extended menu). None of the User’s Logo features in the Extended menu can be changed when the User’s Logo Protect function is enabled. Starting the Projector with a Password When the password function is enabled, you see this screen when you plug in and turn on the projector: Hold down the Num button on the remote control and use the numeric keypad to enter the four digit password. The password screen closes, the numeric keypad is automatically deactivated, and projection begins. Fine-Tuning the Projector If the password is not correct, you see a message prompting you to re-enter the password. If you enter an incorrect password three times in succession, you see the message The projector’s operation will be locked. Request code xxxxx and the projector switches to standby mode for approximately 5 minutes. Write down the request code. Then disconnect the projector’s power cord from the electrical outlet, reconnect it, and turn the projector back on. When you see the Password Protect Release screen again, you can try to enter the correct password. If you enter an incorrect password 30 times in succession, the projector remains locked and you must contact Epson to unlock it. If you have forgotten the password, contact Epson with the request code number that appears in the Password Protect Release screen for assistance. See “Where To Get Help” on page 76. Creating Your Own Startup Screen You can transfer any image from your computer or video source to the projector and then use it as your startup screen. You can also use it as the screen displayed when the projector is not receiving a signal or when you press the A/V Mute button. The image can be a company logo, slogan, photograph, or any other image you want to use. Capturing the Image Start by displaying the image you want to use from either a computer or video source, such as a DVD player. Then follow these steps to capture the image and transfer it to the projector: 1. Press the Menu button on the remote control, highlight the Extended menu, and press Enter. Fine-Tuning the Projector 53 2. Highlight User’s Logo and press Enter. 3. When you see a message asking Choose this image as the user’s logo?, select Yes and press Enter. A selection box displays over the image. 4. Use the pointer button to select the area of the image you want to use. Then press Enter. 5. When you see the message Select this Image?, highlight Yes and press Enter. 6. Use the arrow buttons to select a zoom rate (display size) and press Enter. 7....
Ce manuel est également adapté pour les modèles :TV - PowerLite 1700c/1710c (2.29 mb)