Évaluations - 2, GPA: 4.5 ( )

Fabricant : Gold's Gym Taille : 1.08 mb Nom Fichier : 4582e757-90bb-45d6-9b65-f7f627248fb5.pdf Langue d'enseignement:

• Assembly requires two people. Due to the size and weight of the SYSTEM 200, it should be • Tighten all parts as you assemble them, unless assembled in the location were it will be used. instructed to do otherwise. • Place all parts of the SYSTEM 200 in a cleared THE FOLLOWING TOOLS (NOT INCLUDED) ARE area and remove the packing materials; do not REQUIRED FOR ASSEMBLY: dispose of the packing materials until assembly is • Two (2) adjustable wrenches completed. • One (1) standard screwdriver • The assembly is divided into five stages: 1) frame assembly, 2) press and butterfly arm assembly, • One (1) phillips screwdriver 3) cable and pulley assembly, 4) seat and backrest assembly, and 5) VKR assembly. The hard-• One (1) rubber mallet ware for each stage is packaged separately. • Lubricant, such as grease or petroleum jelly, • Wait until you begin each assembly stage to open and soapy water will also be needed. that parts bag. Assembly will be more convenient if you have the • As you assemble the SYSTEM 200, be sure that following tools: A socket set, a set of open-end or all parts are oriented as shown in the drawings. closed-end wrenches, or a set of ratchet wrenches. FRAME ASSEMBLY 1. Before beginning assembly, be sure that you have read and understand the information in the box above. Press a 2” Square Outer Cap (51) onto each end of the Stabilizer (5). Press a 2” Square Inner Cap (27) into the end of the Base (4). Insert two 5/16” x 2 3/4” Carriage Bolts (14) up through the Stabilizer (5). Insert a 5/16” x 2 1/2” Carriage Bolt (1) up through the Stabilizer. Insert two 5/16” x 2 1/2” Carriage Bolts (1) up through the Base (4). Slide the indicated end of the Base (4) onto the 5/16” x 2 3/4” Carriage Bolts (14) in the Stabilizer (5). Slide the Rear Upright (56) onto the Carriage Bolts. The high side of the bracket on the Rear Upright must be on the side shown. Hand tighten a 5/16” Nylon Locknut (3) onto each Carriage Bolt. Do not tighten the Nylon Locknuts yet. Slide the end of the Brace (88) with the round hole onto the 5/16” x 2 1/2” Carriage Bolt (1) in the Stabilizer (5). Hand tighten a 5/16” Nylon Locknut (3) onto the Carriage Bolt. Attach the end of the Brace with the slotted hole to the Rear Upright (56) with a 5/16” x 2 3/4” Bolt (11), a 5/16” Flat Washer (8), and a 5/16” Nylon Locknut (3). Do not tighten the Nylon Locknuts yet. 1 High Side of Bracket 51 5 14 1 3 Slotted Hole 3 8 56 11 3 1 4 27 51 88 5 FRAME ASSEMBLY 2. Slide the Front Upright (42) onto the 5/16” x 2 1/2” Carriage Bolts (1) in the Base (4). Hand tighten a 5/16” Nylon Locknut (3) onto each Carriage Bolt. Do not tighten the Nylon Locknuts yet. Press a 1” Square Inner Cap (65) into the Front Upright (42). Press 1” Round Inner Cap (49) into each end of the Footrest (83). Attach the Footrest to the Rear Upright (56) with a 5/16” x 2 3/4” Bolt (11), two 5/16” Flat Washers (8), a 1/2” x 1/2” Bushing (87), and a 5/16” Nylon Locknut (3). 3. Press a 2” Square Inner Cap (27) into the indicated end of the Top Frame (55). Press a 1 3/4” Square Inner Cap (44) into each end of the crossbar on the Top Frame. Press two 1” Round Inner Caps (49) into the top of the crossbar. Attach the Top Frame (55) to the Front Upright (42) and the Rear Upright (56) with four 5/16” x 2 3/4” Bolts (11), four 5/16” Flat Washers (8), and four 5/16” Nylon Locknuts (3). Tighten all Nylon Locknuts used in steps 1 through 3. 4. Set two Weight Bumpers (19) on the indicated bracket on the Base (4) as shown. Stack eight Weights (25) on the Weight Bumpers (19). Be sure that all of the Weights are turned so the deepest pin grooves are under the Weights and are on the indicated side. 2 49 87 811 49 3 8 83 56 4 3 1 65 42 3 27 3 11 3 4456 55 8 11 44 42 Crossbar 8 49 4 4 25 19 Pin Grooves 6 AR...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :