Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY. 4. Position the machine on a clear, leveled surface. DO NOT use the machine near water or outdoors. 5. Keep hands away from all moving parts. 6. Always wear appropriate workout clothing when exercising. DO NOT wear robes or other clothing that could become caught in the machine. Running or aerobic shoes are also required when using the machine. 7. Use the machine only for its intended use as described in this manual. DO NOT use attachments not recommended by the manufacturer. 8. Do not place any sharp object around the machine. 9. Disabled person should not use the machine without a qualified person or physician in attendance. 10. Before using the machine to exercise, always do stretching exercises to properly warm up. 11. Never operate the machine if the machine is not functioning properly. CARE AND MAINTENANCE 1. Inspect and tighten all parts before using the machine. 2. The machine can be cleaned using a damp cloth and mild non-abrasive detergent. DO NOT use solvents. 3. Maximum User’s Weight: 300 lbs. WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. SAVE THESE INSTRUCTIONS. 2 WARNING LABEL REPLACEMENT The Warning Label shown here has been placed on the Base Frame. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown. 3 HARDWARE PACK 4 ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the Left and Right Base Frame (#1 & #2) with the Stabilizer (#3) in the mid-span. Secure each end with two M10 x 2 .” Carriage Bolts (#19), . .” Washers (#17), and M10 Aircraft Nuts (#18). Do NOT tighten the Nuts and Bolts yet. B.) Attach a Lower Upright Beam (#5) onto the Right Stabilizer (#2). Secure it with two M10 x 2 .” Carriage Bolts (#19), one 5 .” Bracket (#12), two . .” Washers (#17), and two M10 Aircraft Nuts (#18). Repeat the same procedure to install the other side. NOTE: Do NOT tighten all the nuts and bolts yet. DIAGRAM 1 5 STEP 2 (See Diagram 2) A.) Attach a Diagonal Support (#4) to the Lower Upright Beam (#5) and the Right Base Frame (#2). Secure it to the Lower Upright Beam with two M10 x 3” Carriage Bolts (#20), O 1 .” Bent Washers (#22), and M10 Aircraft Nuts (#18). Secure it to the Right Base Frame with two M10 x 2 .” Carriage Bolts (#19), one 4 .” Bracket (#13), two O .” Washers (#17), and two M10 Aircraft Nuts (#18). B.) Attach a Dip Support (#9) to the Lower Upright Beam. Align the holes and secure them with two M10 x 3 1/8” Carriage Bolts (#21), one Curve Bracket (#11), and two M10 Aircraft Nuts (#18). Repeat the same stop to install the other side. C.) Attach two Upper Upright Beams (#6) onto the Lower Upright Beams (#5). D.) Connect the two Upright Beams with a Cross Brace (#7) in the middle. Secure each side with two M10 x 3” Carriage Bolts (#20), . 1 .” Bent Washers (#22) and M10 Aircraft Nuts (#18). Do NOT tighten all the Nuts and Bolts yet. E.) Attach a Vertical Handle (#8) to the Dip Support. Secure it with one M10 x 1” Allen Bolt (#31) and O .” Bent Washer (#24). Repeat to install the other side. 6 DIAGRAM 2 7 STEP 3 (See Diagram 3) A.) Attach the Chin-up Bar (#10) to the top opening on the two Upper Upright Beams. Secure the Chin-up Bar to each opening with one M8 x 1 5/8” Allen Bolt (#27) and O .” Bent Washer (#34). Cover each opening with an Upright Beam End Cap (#30). B.) Attach the two Arm Pads (#15) onto the Dip Supports. Secure each Arm Pad with two M8 x 2 .” Allen Bolts (#16) and O 5/8” Bent Washers (#26). C.) Attach the Backrest Board (#14) to the Cross Brace (#7). Secure it with two M8 x .” Allen Bolts (#29) and O 5/8” Washers (#28). D.) Securely tighten all Nuts and Bolts previously installed. 8 EXPLODED DIAGRAM 9 Parts list KEY NO. DESCRIPTION Q’ty Left Base Frame 1 Right Base Frame 1 Stabilizer 1 Diagonal Support 2 Lower Upright Beam 2 Upper Upright Beam 2 Cross Brace 1 Vertical Handle 2 Dip Support 2 Chin-up Bar 1 Curve Bracket 2 5 .” Bracket 2 4 .” Bracket 2 Backrest Board 1 Arm Pad 2 M8 x 2 .” Allen Bolt 4 O .” Washer 12 M10 Aircraft Nut 24 M10 x 2 .” Carriage Bolt 12 M10 x 3” Carriage Bolt 8 M10 x 3 1/8” Carriage Bolt 4 O 1 .” Bent Washer 8 2” Base Frame End Cap 4 O .” Bent Washer 2 O 2” Sleeve 2 O 5/8” Bent Washer 4 M8 x 1 5/8” Allen Bolt 2 O 5/8” Washer 2 M8 x .” Allen Bolt 2 Upright Beam End Cap 2 M10 x 1” Allen Bolt 2 6 .” Grip 4 6” Grip 2 O .” Ben...