Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
48. Route the Ab Cable (107) through the Right Upright (2) and under a 90mm Pulley (63). Attach the Pulley and two Half Finger Guards (66) to the Right Base (1) with an M10 x 50mm Bolt (64) and an M10 Nylon Locknut (90). Make sure the Finger Guards are oriented as shown. 49. Wrap the Ab Cable (107) over a 90mm Pulley (63). Attach the Pulley, a Cable Trap (68), and two Half Finger Guards (66) to the lower hole in the indicated “U”-bracket (50) with an M10 x 52mm Bolt (78) and an M10 Nylon Locknut (90). Make sure the Cable Trap and Finger Guards are oriented as shown. 47. Attach a 90mm Pulley (63) inside the Right Seat Frame (3), over the Ab Cable (107), with an M10 x 45mm Bolt (80) and an M10 Nylon Locknut (90). 46 47 48 49 63 99 99 77 90 4 3 101 107 Large Ball Rod 101 3 107 107 63 80 90 64 90 66 66 1 2 63 107 50 63 66 90 66 68 78 19 50. Wrap the Ab Cable (107) under a 90mm Pulley (63). Attach the Pulley, a Cable Trap (68), and two Half Finger Guards (66) to the Right Base (1) with an M10 x 50mm Bolt (64) and an M10 Nylon Locknut (90). Make sure the Cable Trap and Finger Guards are oriented as shown. 52. Wrap the Ab Cable (107) under a 90mm Pulley (63). Attach the Pulley, a Cable Trap (68), and two Half Finger Covers (66) to the Right Base (1) with an M10 x 50mm Bolt (64) and an M10 Nylon Locknut (90). Make sure the Cable Trap and Finger Guards are oriented as shown. 54. Wrap the Ab Cable (107) under a 90mm Pulley (63). Attach the Pulley, a Cable Trap (68) and two Half Finger Guards (66) to the Right Base (1) with an M10 x 50mm Bolt (64) and an M10 Nylon Locknut (90). Make sure the Cable Trap and Finger Guards are oriented as shown. 53. Wrap the Ab Cable (107) over a 90mm Pulley (63). Attach the Pulley, a Cable Trap (68), and two Half Finger Guards (66) to the lower hole in the indicated “U”-bracket (50) with an M10 x 52mm Bolt (78) and an M10 Nylon Locknut (90). Make sure the Cable Trap and Finger Guards are oriented as shown. 51. Wrap the Ab Cable (107) over a 90mm Pulley (63). Attach the Pulley, a Cable Trap (68), and two Half Finger Guards (66) at the second hole from the bottom of the two Pulley Plates (51) with an M10 x 52mm Bolt (78) and an M10 Nylon Locknut (90). Make sure the Cable Trap and Finger Guards are oriented as shown. 50 51 52 53 54 90 66 107 66 64 68 63 1 90 51 68 63 107 66 66 78 63 1 66 66 90 68 64 107 107 107 78 66 66 50 68 63 63 68 66 66 1 90 64 90 20 55. Wrap the Ab Cable (107) over a 90mm Pulley (63). Attach the Pulley and the two Quarter Finger Guards (105) to the Right Upright (2) with an M10 x 108mm Bolt (72), an M10 Washer (99), and an M10 Nylon Locknut (90). Make sure that the rod is inserted through both Finger Guards and is over the Cable. 57. Attach a Backrest (9) to the Backrest Frame (53) with four M6 x 16mm Screws (88). Slide the Backrest Frame (53) into the Left Upright (26). Engage the Knob (43) into the Upright and Backrest Frame, and turn it clockwise until it is tight. 58. Attach a Seat (8) to the Left Seat Frame (27) with four M6 x 16mm Screws (88). Repeat this step with the other Seat (8) and the Right Seat Frame (not shown). 56. Tighten the Weight Cable (110) into the Weight Tube (not shown) until all the slack is taken out of the cables. Tighten the M12 Nut (49) on the Weight Cable against the M12 Washer (33). 55 56 57 58 90 99 2 63 72 Rod 107 105 105 33 49 110 9 53 26 88 88 43 8 27 88 88 Seat Assembly 21 59. Attach a Backrest (9) to the Right Upright (2) with four M6 x 16mm Screws (88). 60. Press the two Shroud Covers (11) onto the Shroud (10). Attach the Shroud to the Right Top Frame (5) and the Center Base (52) with four M6 x 22mm Bolts (87), four M6 Washers (97), and four M6 Nylon Locknuts (92). Be careful not to scratch yourself when reaching through the hole in the Shroud. 59 60 2 9 88 88 87 97 97 92 92 11 10 5 87 97 97 92 92 11 52 22 61. Attach the Lock Plate (21) to the Right Seat Frame (3) with an M8 x 68mm Shoulder Bolt (41), an M8 Washer (98), and an M8 Nylon Locknut (91). Do not overtighten the Locknut; the Lock Plate must be able to pivot easily. Attach the Leg Pin (24) to the Right Seat Frame (3) with an M4 x 16mm Self-tapping Screw (89). Insert the Leg Pin through the Leg Lever (4) and the Lock Plate (21). 63. Slide two Leg Lever Foam Pads (35) onto the Leg Lever (4). 62. Slide the Pad Tube (16) through the Right Seat Frame (3). Slide two Small Foam Pads (18) onto the Pad Tube. Press two Foam Caps (17) into the Pad Tubes. 61 62 91 98 3 4 89 24 21 41 3 16 18 17 18 17 63 35 35 4 64. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in ADJUSTMENTS, beginn...
Ce manuel est également adapté pour les modèles :Formateurs - 831.154020 (4.68 mb)
Formateurs - 831.154020 (4.68 mb)
Formateurs - 831.154020 (4.68 mb)
Formateurs - 831.154020 (4.68 mb)